You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Battlebot Weapon : Trouble spinning up by satacoy » Thu, 2019-04-04 07:29 |
0 |
by satacoy Thu, 2019-04-04 07:29 |
|
|
Issues running a gimbal motor by ksau » Thu, 2021-03-11 16:44 |
0 |
by ksau Thu, 2021-03-11 16:44 |
|
|
Speed control issues w. hub motors by akerblad » Sun, 2019-04-07 17:22 |
0 |
by akerblad Sun, 2019-04-07 17:22 |
|
|
Got the judders by Phill Dixon » Sun, 2018-05-13 17:45 |
0 |
by Phill Dixon Sun, 2018-05-13 17:45 |
|
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Additional Status Messages by louisgcr » Tue, 2021-12-21 08:04 |
0 |
by louisgcr Tue, 2021-12-21 08:04 |
|
|
Motor draws current (up to 120 A), but doesn't turn by Heimfried » Sun, 2020-03-01 22:21 |
0 |
by Heimfried Sun, 2020-03-01 22:21 |
|
|
Parsing PPM data from CAN Bus by walleywalker » Sun, 2021-12-26 23:57 |
0 |
by walleywalker Sun, 2021-12-26 23:57 |
|
|
Vesc_tool running error by kwlimm » Sun, 2020-01-19 10:01 |
0 |
by kwlimm Sun, 2020-01-19 10:01 |
|
|
Limiting Down hill speed by dbau » Sat, 2022-01-29 06:54 |
0 |
by dbau Sat, 2022-01-29 09:19 |
|
|
Arduino- UART Library Question... by arranto12 » Sun, 2022-01-02 09:57 |
0 |
by arranto12 Sun, 2022-01-02 09:57 |
|
|
Vesc 75/300 max current by a727dd » Wed, 2020-03-04 04:34 |
0 |
by a727dd Wed, 2020-03-04 04:34 |
|
|
VESC apps by bosko » Thu, 2020-01-23 18:28 |
0 |
by bosko Thu, 2020-01-23 18:28 |
|
|
HFI and braking by aethyr » Thu, 2020-03-19 21:01 |
0 |
by aethyr Thu, 2020-03-19 21:01 |
|
|
How to start with vesc source code ? by cmarc » Tue, 2020-01-28 15:48 |
0 |
by cmarc Tue, 2020-01-28 15:48 |
|
|
Using VESC for a Linear Motor by Toshi Sharma » Wed, 2022-01-12 13:11 |
0 |
by Toshi Sharma Wed, 2022-01-12 13:11 |
|
|
VESC Calculator by lmochsner » Thu, 2020-04-02 05:13 |
0 |
by lmochsner Thu, 2020-04-02 05:13 |
|
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
|
PPM Position over CAN bus? by walleywalker » Thu, 2021-12-02 18:47 |
0 |
by walleywalker Thu, 2021-12-02 18:47 |
|
|
How can I get current data from VESC to stm32f446re by hyedo » Sun, 2022-01-23 19:38 |
0 |
by hyedo Sun, 2022-01-23 19:38 |
|
|
Welding with the VESC by doomy1986 » Mon, 2020-04-13 14:38 |
0 |
by doomy1986 Mon, 2020-04-13 14:38 |
|
|
Flipsky VESC 4.20 with 5.1 Firmware PWM input offset by mantisrobot » Thu, 2020-11-05 12:24 |
0 |
by mantisrobot Thu, 2020-11-05 12:24 |
|
|
Payment by Paypal. by ThierryGTLTS » Wed, 2017-09-06 14:38 |
0 |
by ThierryGTLTS Wed, 2017-09-06 17:50 |
|
|
Porting VESC to STML4 by Vince_1618 » Fri, 2022-10-28 14:01 |
0 |
by Vince_1618 Fri, 2022-10-28 14:01 |
Log in to post new content in the forum.
