You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
ScholarOn by kelly edwards » Thu, 2021-03-11 10:54 |
0 |
by kelly edwards Thu, 2021-03-11 10:54 |
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
How the saliency is affecting the High frequency signal injection? by SOURAV UK » Sun, 2020-05-03 11:35 |
0 |
by SOURAV UK Sun, 2020-05-03 11:35 |
|
VESC App - Android - "App not installed" error by KColborne » Mon, 2023-03-27 22:11 |
0 |
by KColborne Mon, 2023-03-27 22:11 |
|
Dual VESC via CAN by scholtylicious » Sat, 2021-03-13 15:56 |
0 |
by scholtylicious Sat, 2021-03-13 15:56 |
|
PPM Arduino throttle AND UART Bluetooth Monitor AND brake lever for braking by vescsci » Fri, 2020-06-12 10:55 |
0 |
by vescsci Fri, 2020-06-12 10:55 |
|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce » Mon, 2021-03-15 03:31 |
0 |
by Bruce Mon, 2021-03-15 03:31 |
|
Comms plug and leads by craig w » Fri, 2021-12-24 00:25 |
0 |
by craig w Fri, 2021-12-24 00:25 |
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 » Wed, 2019-10-23 23:12 |
0 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
|
PAS only one signal + BLE by sifourquier » Fri, 2021-12-31 19:08 |
0 |
by sifourquier Fri, 2021-12-31 19:08 |
|
Using the parameter editor by dqt boi » Thu, 2019-10-24 23:31 |
0 |
by dqt boi Thu, 2019-10-24 23:31 |
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
Vesc gps control by Erik » Thu, 2019-11-14 20:38 |
0 |
by Erik Thu, 2019-11-14 20:38 |
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
|
Calculator by kstuck » Tue, 2019-12-10 18:30 |
0 |
by kstuck Tue, 2019-12-10 18:30 |
|
How to use an IMU and a PPM remote parallel by Gos1 » Tue, 2022-10-25 15:28 |
0 |
by Gos1 Wed, 2022-10-26 10:57 |
|
Issue with VESC I/O on donkey car by baluja » Fri, 2022-10-28 02:56 |
0 |
by baluja Fri, 2022-10-28 02:56 |
|
Inquiry about Incremental and Absolute Encoders in VESC for Robotics by sivanhere » Fri, 2022-10-28 21:02 |
0 |
by sivanhere Fri, 2022-10-28 21:02 |
|
What do i need? by Robert Thomas » Fri, 2022-09-16 21:39 |
0 |
by Robert Thomas Fri, 2022-09-16 22:12 |
|
VESC Wand shows INF and 100% Batt by BLKFLD » Sat, 2020-09-26 04:48 |
0 |
by BLKFLD Sat, 2020-09-26 04:48 |
Log in to post new content in the forum.