You are here
VESC Development and Beta Testing
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Sticky:
About this forum by benjamin » Tue, 2020-03-17 10:21 |
2 |
by clamdad Mon, 2022-02-21 15:12 |
|
|
Firmware 5.03 (Page: 1, 2, 3, 4)
by benjamin » Sun, 2021-02-28 21:28 |
188 |
by irene167 Wed, 2022-09-14 08:40 |
|
|
Firmware 5.00 (Page: 1, 2)
by benjamin » Tue, 2020-03-17 16:46 |
54 |
by Andrzej Jarosz Sun, 2021-08-01 02:01 |
|
|
Firmware 6.00 by benjamin » Wed, 2022-01-19 16:49 |
33 |
by MaSh Sat, 2024-02-24 18:01 |
|
|
Firmware 5.02 by benjamin » Sun, 2020-05-03 22:38 |
31 |
by venom121212 Mon, 2021-09-27 19:07 |
|
|
No UART Output on VESC6 MKIV by uwala » Sun, 2020-10-25 12:13 |
8 |
by tsm Tue, 2021-12-21 15:20 |
|
|
Help with firmware bootloader on UAVCAN by jmachuca77 » Mon, 2021-03-15 20:25 |
6 |
by jmachuca77 Mon, 2021-03-29 23:40 |
|
|
CAN bus protocol upgrade thoughts by Pimousse » Fri, 2020-03-20 15:37 |
6 |
by jmachuca77 Fri, 2021-02-26 23:54 |
|
|
Flashing custom code for 100/250 bricked the board by pe » Tue, 2021-11-16 14:14 |
6 |
by kubark42 Fri, 2021-12-17 16:37 |
|
|
[Solved] Bricked VESC when trying to upload a firmware built from source by cfv-naio » Fri, 2020-08-21 16:28 |
6 |
by Bill Somerville Fri, 2020-11-06 23:18 |
|
|
[solved] Where the motor configuration signature is from? by Beren » Thu, 2021-06-17 20:55 |
5 |
by rafeh1 Mon, 2022-11-07 00:45 |
|
|
How to tell what HW version I have and set conf_general.h by jmachuca77 » Fri, 2021-02-19 19:21 |
4 |
by danilolattaro Mon, 2021-04-12 19:38 |
|
|
Save state data on vesc? by NuRxG » Thu, 2020-04-09 06:44 |
4 |
by ProgramThyself Sat, 2020-09-12 08:42 |
|
|
Custom command testing by felixcollins » Thu, 2020-10-15 23:31 |
3 |
by felixcollins Wed, 2020-10-21 03:18 |
|
|
CANopen integration by blevruz » Wed, 2022-10-05 10:33 |
3 |
by benjamin Fri, 2022-10-14 17:12 |
|
|
VESC Express by velolac » Mon, 2023-03-13 14:03 |
3 |
by pc.buher Fri, 2023-08-18 16:00 |
|
|
Firware 5.2 by julitosanse » Wed, 2021-01-27 03:59 |
2 |
by zaporka Wed, 2021-02-17 16:42 |
|
|
ArduPilot collaboration by magicrub » Mon, 2021-04-19 05:21 |
2 |
by frank Fri, 2021-05-21 19:10 |
|
|
App development and Debug by dpeinado » Wed, 2022-03-30 11:39 |
2 |
by dpeinado Thu, 2022-06-23 12:42 |
|
|
the latest vesc6 version by Andy Moon » Wed, 2021-07-21 11:00 |
2 |
by frank Tue, 2022-08-23 12:23 |
|
|
Migrate to STM32H7 by ERG » Sun, 2022-06-19 19:35 |
2 |
by brokulp Sun, 2024-02-11 13:36 |
|
|
[SOLVED] trying to get the new release version 5.03 but when I order the free version, the linux release version doesn't show up by geoporus » Wed, 2022-06-15 10:58 |
1 |
by geoporus Wed, 2022-06-15 11:01 |
|
|
use SWDIO and SWCLK as normal GPIO ? by lqbweb » Mon, 2022-08-01 00:30 |
1 |
by snovotill Sat, 2022-10-29 18:28 |
|
|
why the motor current cant reach more than 2A? by chijay » Sat, 2021-03-13 16:38 |
1 |
by microcai Fri, 2021-08-13 14:50 |
|
|
PPM+UART: Priority to UART on HW6? by Filcas » Sat, 2021-04-03 11:05 |
1 |
by mark99 Sun, 2021-07-04 13:15 |
Log in to post new content in the forum.
