Hi,
I updated to the latest fw but when I try to run the input wizard, I'm always asked to update the fw to a newer version.
Here are the screenshots to the input wizard message dialog and the current firmware information:
https://www.dropbox.com/s/ljg5o79ljqrubkx/firmware_widget.png?dl=0
https://www.dropbox.com/s/8s04nsldrzcr2va/input_setup_wizard.png?dl=0
Hey Guys
I recently embarked on my first DIY board and with that, my first experience with the VESC tool. Please excuse my ignorance or lack of understanding of any aspects.
Bought a Flipsky6.6 Dual (i know, i probably should have spent the extra and just got a proper VESC) and set up using the VESC tool, paid for and downloaded from here.
Initially went through all the standard initial setup wizards as shown in the documentation here, as well as YouTube videos.
The motors simply don't seem to operate properly.
Hello,
I purchased VESC Tool at 2020-01-01 (Silver) and according to its change log it is version 1.29.
Every time I start it, a windows occures and tells me a newer version would be available and I schould use it. How to get an update?
Gruß, Günter
Hi everyone!
I have downloaded the latest Vesc Tool 2.2 and I'm having problems when flashing a new firmware
My Vesc is a dual Flipsky 4.20 which is basically two 4.12 (4.10) VESCs on a single PCB paired via internal CAN
I used the Ackmaniac's vesc tool previously with the FW version 3.103.
I connected the VESC via USB, disabled the can forwarding and tried to update the single side only.
The RT data is disabled.
I get the following errors in the debug console
Hello all,
I've been building electric bikes for 4 years now. I recently purchased a 200 amp Maytech VESC and a motor capable of 200 amps continuous. The VESC tool software, however, does not allow over 120 amps for the motor or battery settings. Does anybody know of a way to override this? Thank you for your help!
Hello,
I am working on a project, in which I need to control a linear actuator. When I tried to use VESC's FOC mode to do the auto tuning of the encoder offset under the tab 'encoder', I found the actuator keep moving in one direction without reverse in direction. The encoder realtime data plot showed a smooth curve of the encoder reading so I don't think the encoder is out of order. I have tried a rotary motor and got the tuning done. Anyone have similar experience that can share with me?
Hi
I have a BRH5065-140kV outrunner with a Flipsky 4.12, and I need a very simple setup with my throttle (0,8-2,6V). Linear speed with max torque, and full freewheeling when the throttle is in neutral.
In ADC Duty Cycle, I have linear speed (don't know about the torque, I'm not that far in my testing), but the motor is braking, and the current seems to be 0-0,10A. CH1 and CH2 clearly shows 0,0%, so I don't think it's the mapping. (I do not have CH2, but haven't figured out how to disable it).
I am trying to start the VESC tool but it stays empty.
The first time I started it I got a security warning about a untrusted programs and I selected 'run anyway' and it showed the UI. It did not seem responsive and did not resize. I plugged in the USB cable to the VESC. I got an error message about old firmware and reduced communication and after this it did not respond.
Now every time I start the program it stays empty.
Thanks for checking out my post, I previously made an android app to control my old electric skateboard (did not use VESC) and I am trying to get it working on my new build (uses VESC). The app sends bytes to an arduino that creates a 1ms to 2ms PWM signal for input to the VESC. On windows I followed the Input wizard documentation for PPM and it seemed to work well. I wrote the configuration to the VESC and disconnected it from my laptop but then it stopped working. So I plugged in the VESC again to my laptop and without auto connecting it, it would work again.
