|
Normal topic
|
VESC 75/300 repair
by mah on Tue, 2025-07-01 16:16 |
VESC Original Hardware |
|
Normal topic
|
Connecting VESC (FSESC75200) to Flight Controller (Matek H743) for Rover — Setup and Recommendations
by ispor4en on Fri, 2025-06-27 21:36 |
Projects incorporating VESC technology |
|
Normal topic
|
Switch between pre-defined profiles over UART
by PutridFox on Sun, 2025-06-15 13:11 |
General discussion |
|
Normal topic
|
Innotrace X1 motor controller for Bafang m620 UART with VESC firmware
by TPEHAK on Tue, 2025-06-10 22:00 |
VESC Firmware |
|
Normal topic
|
Flipsky 75100 V2 with Maxon 386675
by GoFast99 on Thu, 2025-06-05 20:54 |
Third Party Hardware |
|
Normal topic
|
base on VESC6_MkVI
by gavin on Wed, 2025-06-04 15:48 |
General discussion |
|
Normal topic
|
Throttle cutout or no response...MK6 + CA3 + Older Stand alone shunt
by craigoroszi on Tue, 2025-06-03 05:24 |
Third Party Hardware |
|
Normal topic
|
Flipsky and Trampa getting two very different detected resistances on same motor!
by colmor on Wed, 2025-05-28 22:52 |
General discussion |
|
Normal topic
|
Reversed polarity on one of my controllers when setting up
by jsherbz92 on Sun, 2025-05-25 15:16 |
General discussion |
|
Normal topic
|
Cruise control
by palaga on Tue, 2025-05-20 09:20 |
General discussion |
|
Normal topic
|
connect android to controller?
by craigoroszi on Mon, 2025-05-19 20:53 |
VESC Tool |
|
Normal topic
|
vesc 75100 variations for a kart build
by elbracer on Mon, 2025-05-19 19:57 |
General discussion |
|
Normal topic
|
Motor seize and ERPM current ramp speed
by krabsheva on Tue, 2025-05-13 06:49 |
General discussion |
|
Normal topic
|
Sensorless Homing: Move motor between two endstops
by LISMS on Fri, 2025-05-09 00:50 |
Projects incorporating VESC technology |
|
Normal topic
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller?
by avaid on Thu, 2025-05-08 12:57 |
General discussion |
|
Normal topic
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish
by Shreeram2311 on Tue, 2025-05-06 02:40 |
VESC Tool |
|
Normal topic
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß
by Oriessin on Sat, 2025-04-26 07:38 |
General discussion |
|
Normal topic
|
What is the current state of mcus support?
by il_piccione on Fri, 2025-04-25 09:47 |
General discussion |
|
Normal topic
|
Is BMS Tool compatible with LTO batteries?
by SteveBrantley on Fri, 2025-04-18 23:12 |
General discussion |
|
Normal topic
|
Repurposed Hyundai Ioniq HSG Hybrid Starter Generator as motor - crunching/cogging
by patracy on Sat, 2025-04-12 04:42 |
General discussion |
