You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC debugging without optimization by Siverian on Sun, 2020-04-05 01:47 |
by Siverian Sun, 2020-04-05 01:47 |
VESC Firmware | ||
|
VESC Tool Battery Settings for 5S Lipo by Bildoon on Sat, 2020-04-04 23:28 |
1 |
by Bildoon Mon, 2020-04-06 01:24 |
VESC Tool | |
|
Delayed start for slave motor by rsknudsen-dk on Mon, 2020-04-06 10:06 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
General discussion | ||
|
FOC configuration when resistance is measured as R=0. by Roger Wolff on Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
VESC Tool | |
|
Chibios/RT Virtual Com Port Driver. by Sanjoy on Wed, 2017-06-07 22:53 |
15 |
by bb67 Tue, 2020-04-07 22:14 |
VESC6 Beta | |
|
help with vesc real time data trouble shooting by stefann on Wed, 2020-04-08 23:02 |
by stefann Wed, 2020-04-08 23:02 |
VESC Tool | ||
|
help with vesc real time data trouble shooting by stefann on Wed, 2020-04-08 23:03 |
by stefann Wed, 2020-04-08 23:03 |
VESC Tool | ||
|
Using STM32F407 for a custom board by kapek on Mon, 2020-04-06 04:16 |
2 |
by vadicus Fri, 2020-04-10 06:31 |
General discussion | |
|
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques on Sat, 2020-04-11 09:20 |
by peignier jacques Sat, 2020-04-11 09:21 |
Feature Requests | ||
|
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool | ||
|
Welding with the VESC by doomy1986 on Mon, 2020-04-13 14:38 |
by doomy1986 Mon, 2020-04-13 14:38 |
General discussion | ||
|
rangeextender build - Vesc trying to fry itself by DIY_rangeextender on Tue, 2020-03-17 08:43 |
1 |
by bgdwiepp Wed, 2020-04-15 01:28 |
Third Party Hardware | |
|
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 03:27 |
by AllenFF Wed, 2020-04-15 03:27 |
General discussion | ||
|
Servo Control PPM by jonthie on Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
VESC Tool | |
|
Newbie Help please, Longer run time? by Bildoon on Mon, 2020-04-06 02:00 |
1 |
by linsus Thu, 2020-04-16 14:18 |
General discussion | |
|
4 vesc motors at once? by i-make-robots on Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
General discussion | |
|
No, BLDC is not dead. by Pimousse on Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
General discussion | |
|
How to update firmware over CAN bus by andrii619 on Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
General discussion | |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
|
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
VESC Tool |
Pages
