You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Runtime motor control with CAN by Davidepolpi91 on Fri, 2024-03-15 15:12 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
General discussion | ||
|
Maximum cable lengths between VESC, battery pack and motor? by sandersesurf on Sun, 2024-01-14 07:55 |
3 |
by bww129 Fri, 2024-03-15 05:46 |
General discussion | |
|
3v3 Regulator fried? How to check if STM was affected too? by Seudo on Fri, 2024-02-16 19:48 |
1 |
by bww129 Fri, 2024-03-15 05:36 |
General discussion | |
|
Changing current sense output offset by bww129 on Fri, 2024-03-15 05:27 |
by bww129 Fri, 2024-03-15 05:27 |
General discussion | ||
|
Getting IMU Data over UART by Mido on Wed, 2021-04-21 12:30 |
7 |
by MrFobwatch Fri, 2024-03-15 03:05 |
General discussion | |
|
PyVESC - Realtime Data - Experiment Export .csv file by Eric_IraLo on Wed, 2024-03-13 20:03 |
3 |
by Eric_IraLo Thu, 2024-03-14 20:14 |
General discussion | |
|
being able to connect VESC 6 MK VI with servo by mmobayed on Mon, 2024-03-11 20:22 |
1 |
by Srihari293 Wed, 2024-03-13 08:45 |
General discussion | |
|
Control VESC with PPM and Simultaneously get Data with CAN by warhawk on Wed, 2024-03-13 06:23 |
by warhawk Wed, 2024-03-13 06:42 |
VESC Tool | ||
|
VESC 75/300 + Scorpion 7050 300kv for Combat Robotics Weapon by DabbingSnail on Mon, 2024-03-11 22:27 |
1 |
by electricfox Mon, 2024-03-11 23:16 |
General discussion | |
|
Wh/mi trip calculation error by devcic on Mon, 2024-03-11 16:44 |
by devcic Mon, 2024-03-11 16:44 |
VESC Tool | ||
|
Newbie question : How to switch to RPM mode ? by Lezard on Thu, 2024-02-29 19:30 |
1 |
by Lezard Mon, 2024-03-11 15:18 |
VESC Tool | |
|
VESC hybrid drone generator by sander123 on Thu, 2024-03-07 10:55 |
1 |
by electricfox Sat, 2024-03-09 19:02 |
General discussion | |
|
Power button works only as turn ON button, but not working as turn OFF by zmei116 on Tue, 2020-05-26 18:52 |
4 |
by electricfox Sat, 2024-03-09 18:57 |
VESC Original Hardware | |
|
Cant copy data from CAN Debugger by testusernameimsorry on Sat, 2024-03-09 11:52 |
by testusernameimsorry Sat, 2024-03-09 11:52 |
VESC Tool | ||
|
G60 motor hall wires pinout by Talonkid119 on Wed, 2024-03-06 03:43 |
by Talonkid119 Wed, 2024-03-06 03:43 |
General discussion | ||
|
Linux QT ERROR HOW TO FIX by Veerapandiyan on Tue, 2024-03-05 12:26 |
1 |
by Veerapandiyan Tue, 2024-03-05 13:55 |
VESC Tool | |
|
DIY BLDC Motor Driver MCU by hamidiye suları on Fri, 2024-02-23 12:51 |
1 |
by hamidiye suları Tue, 2024-03-05 12:26 |
Third Party Hardware | |
|
MTPA by hummina on Tue, 2024-02-20 19:54 |
1 |
by Rohan_Suresh_babu Mon, 2024-03-04 06:21 |
General discussion | |
|
IMPSM Motor and Gearing by baein on Tue, 2022-01-25 11:19 |
5 |
by Rohan_Suresh_babu Sat, 2024-03-02 12:18 |
General discussion | |
|
vesc_tool 6 and vesc 4.12 -> motor setup of small outrunner not working by Gawarmel on Thu, 2024-02-29 14:56 |
by Gawarmel Thu, 2024-02-29 14:56 |
VESC Tool |
Pages
