You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Increasing low rpm torque in FOC mode by galp on Mon, 2019-01-21 18:15 |
1 |
by sam.vanratt Thu, 2019-01-24 00:02 |
General discussion | |
|
VESC on 48V 1500W HUB motor by jordanlow on Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
VESC Original Hardware | |
|
Connect both hall and incremental quadrature encoders by vpl on Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
General discussion | |
|
VESC and Motors for sale. by raess on Thu, 2019-01-24 22:41 |
by raess Thu, 2019-01-24 22:41 |
General discussion | ||
|
VESC Tool Instructions by brschaefer74 on Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
General discussion | |
|
Travis CI by paltatech on Tue, 2019-01-29 00:57 |
by paltatech Tue, 2019-01-29 00:57 |
VESC Firmware | ||
|
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
|
Does the code right by jennyxcy2008 on Mon, 2019-01-28 02:57 |
7 |
by jennyxcy2008 Tue, 2019-01-29 04:52 |
VESC Firmware | |
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman on Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
Third Party Hardware | |
|
Calculate HW_DEAD_TIME_VALUE by sunsam8 on Tue, 2019-01-29 01:47 |
1 |
by paltatech Thu, 2019-01-31 04:54 |
VESC Firmware | |
|
VESC 6 with 3 phase shunts to ground instead by shaman on Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
Third Party Hardware | |
|
Bus bar and heavy copper PCBs by lopezcontreras on Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
Third Party Hardware | |
|
Fault:DRV8302 DUAL V4 by Lzx19961014 on Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
General discussion | |
|
Dual brushed motors from 1 R/C stick? by VESC1 on Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
General discussion | |
|
Where to order plastic sleeve for VESC by braingame26 on Thu, 2019-02-07 16:34 |
by braingame26 Thu, 2019-02-07 16:34 |
Third Party Hardware | ||
|
Sensored FOC not working by Jarson on Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
VESC Tool | |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu on Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
VESC Tool | |
|
Sub zero temperature VESC412 issues by jetigm on Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
General discussion | |
|
Sudden vesc unresponsiveness by nolander on Mon, 2019-01-07 22:29 |
6 |
by Caustic_Zinc Mon, 2019-02-11 09:32 |
VESC Tool | |
|
SPI Encoder communications with AS5047 by vadimz on Sun, 2018-10-28 16:55 |
3 |
by Guillaume227 Mon, 2019-02-11 23:14 |
VESC Firmware |
Pages
