You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Request: Report hall sensor tables. by Roger Wolff on Thu, 2018-05-17 15:28 |
7 |
by Tilman Baumann Mon, 2018-08-06 12:24 |
General discussion | |
|
Problem- Regen tripping out BMS on battery pack by jasontwd on Sun, 2018-07-29 10:10 |
2 |
by jzy1115 Tue, 2018-07-31 06:11 |
General discussion | |
|
External power-side board by HansPeterHaastrup on Mon, 2018-07-30 14:53 |
5 |
by HansPeterHaastrup Mon, 2018-07-30 18:23 |
Third Party Hardware | |
|
HW advice : repair , vesc 4.12, vesc 6.4 or better wait ? by frameto on Sun, 2017-11-19 21:36 |
1 |
by josh Thu, 2018-07-26 18:47 |
Third Party Hardware | |
|
ADC Voltage Mapping wizard broken by TechAUmNu on Tue, 2018-07-24 23:58 |
1 |
by TechAUmNu Wed, 2018-07-25 01:46 |
VESC Tool | |
|
More detail in tool tips by TechAUmNu on Mon, 2018-07-23 20:15 |
2 |
by TechAUmNu Tue, 2018-07-24 13:52 |
VESC Tool | |
|
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
|
Question to get a new Motor Running by speedy on Fri, 2018-07-20 07:59 |
1 |
by frank Fri, 2018-07-20 10:23 |
General discussion | |
|
I have soldered MPU 9150 onto my ESC - How can I confirm that it is working? by delond on Sat, 2018-07-14 15:05 |
2 |
by lock Tue, 2018-07-17 02:26 |
General discussion | |
|
Configurable Beta factor for motor NTC. by Danny Bokma on Tue, 2017-09-05 21:29 |
11 |
by slapshot136 Sun, 2018-07-15 20:05 |
Feature Requests | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
Programming NRF51822 Module with ST-Link v2 by koralle on Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
General discussion | |
|
Bad detection problem by baron456 on Fri, 2018-06-29 17:56 |
5 |
by frank Fri, 2018-07-13 14:41 |
VESC Tool | |
|
Updating fw by Phill Dixon on Fri, 2018-07-06 19:30 |
1 |
by frank Fri, 2018-07-13 13:19 |
General discussion | |
|
FW Vesc-Tool V0.95 by Meche on Mon, 2018-07-09 21:07 |
1 |
by Meche Wed, 2018-07-11 16:29 |
General discussion | |
|
Overheat by Phill Dixon on Tue, 2018-07-03 19:07 |
1 |
by frank Tue, 2018-07-10 09:51 |
General discussion | |
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
VESC Control over NRF by Christian on Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
VESC Firmware | |
|
servo input by Roger Wolff on Tue, 2018-07-03 07:50 |
by Roger Wolff Tue, 2018-07-03 07:50 |
VESC Firmware | ||
|
Help with Built-in NRF24 and custom remote by solidgeek on Thu, 2017-06-15 00:35 |
15 |
by m.juan Mon, 2018-07-02 18:06 |
VESC6 Beta |
Pages
