You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne on Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
VESC Tool | |
|
VESC 75/300 Frying in BLDC Regen by ezonca on Fri, 2020-10-23 21:53 |
3 |
by TechAUmNu Thu, 2020-10-29 13:43 |
VESC Original Hardware | |
|
Flipsky ESC 6.6 - How to Compile? [fixed] by hoeken on Tue, 2021-08-31 03:33 |
3 |
by alexantosh Wed, 2021-12-01 18:55 |
VESC Firmware | |
|
Setup parameters for battery in VESC Tool by Ulrich on Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
VESC Tool | |
|
Vesc 6 MKIV ? by mchatain on Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
VESC Original Hardware | |
|
Sensorless temperature compensation by ESCam on Fri, 2018-12-14 19:38 |
3 |
by Roby_88 Sat, 2023-03-11 17:39 |
Feature Requests | |
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin on Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
General discussion | |
|
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion | |
|
VESC4 phase shunt by Rico on Tue, 2019-05-21 16:09 |
3 |
by svs Thu, 2019-08-08 08:41 |
VESC Firmware | |
|
VESC HD60T discontinued? by RickBoerma on Thu, 2021-12-02 15:58 |
3 |
by RickBoerma Wed, 2021-12-08 12:56 |
General discussion | |
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
Play Store - No App - Missing by TooSlow2Care on Mon, 2022-02-14 20:18 |
3 |
by TooSlow2Care Tue, 2022-02-15 19:40 |
VESC Tool | |
|
What is ADC3 used for in VESC6 by Tilman Baumann on Tue, 2018-04-10 11:12 |
3 |
by Gos1 Mon, 2023-06-26 13:56 |
VESC Original Hardware | |
|
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot on Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
General discussion | |
|
Limp mode via CAN by totalgeek9224 on Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
Feature Requests | |
|
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion | |
|
Dual VESC and One Motor Stops Spinning by f0n on Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
VESC Tool | |
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
|
Generator app by arvidb on Sat, 2018-09-22 01:03 |
3 |
by stiganielsen Fri, 2019-09-20 14:29 |
VESC Firmware |
Pages
