You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
How to Enable kill switch support in Firmware 5.03 by iserai2r on Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
VESC Tool | |
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
Реверс вращения двигателя by Wolod5 on Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
VESC Tool | |
FOC for BDC? by SlimSh8y on Thu, 2018-07-12 23:05 |
11 |
by JanneHooo Fri, 2023-10-13 18:20 |
VESC Tool | |
Detection failed. Reason: -11 by Eco Delsbo on Fri, 2019-05-03 12:01 |
10 |
by Gatze Wed, 2020-03-18 22:04 |
VESC Tool | |
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
VESC Tool | |
Vesc PAS (Pedal Assist) by Evwan on Sat, 2022-07-02 04:37 |
4 |
by Sandro luis Fri, 2023-12-15 02:40 |
VESC Tool | |
Difference between regular and 'setup' values in logged csv by aUser on Tue, 2024-04-23 14:03 |
by aUser Tue, 2024-04-23 14:03 |
VESC Tool | ||
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
Writing value to both VESCs on FocFox Unity by agraham on Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
VESC Tool | |
how to communication with arduino on vesc via CAN by yuri12 on Tue, 2022-02-08 13:16 |
by yuri12 Tue, 2022-02-08 13:16 |
VESC Tool | ||
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
VESC Tool for Android & GPS/GNSS sharing? by ahagge on Fri, 2021-10-01 05:04 |
by ahagge Fri, 2021-10-01 05:04 |
VESC Tool | ||
How to update VESC Tool? by Heimfried on Wed, 2020-02-05 10:35 |
2 |
by marialoise Fri, 2020-03-13 20:20 |
VESC Tool | |
Update fail from FW3.58 to 3.61 by sachs2019 on Tue, 2019-09-10 15:51 |
7 |
by AlmaRaposa Thu, 2021-03-11 17:44 |
VESC Tool | |
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik on Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
VESC Tool | |
How do I disable brake? by moo10032 on Tue, 2021-02-23 08:09 |
by moo10032 Tue, 2021-02-23 08:10 |
VESC Tool | ||
Error on log-file recording: Could not get Positioning Working by hpb66 on Mon, 2022-05-23 08:23 |
by hpb66 Mon, 2022-05-23 08:23 |
VESC Tool | ||
Help i can not setup my motors by jakson01 on Fri, 2022-09-09 18:37 |
by jakson01 Fri, 2022-09-09 18:37 |
VESC Tool | ||
Incorrect speed too high by Michele84 on Wed, 2021-07-21 15:48 |
by Michele84 Wed, 2021-07-21 15:48 |
VESC Tool |