You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Can bus and Arduino by Snabelost on Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
General discussion | |
|
Issue in encoder mode by limeng06217 on Tue, 2020-02-25 16:48 |
2 |
by limeng06217 Tue, 2020-02-25 16:56 |
General discussion | |
|
SpaceVESC, a modular small VESC by SpaceVESCproject on Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
Third Party Hardware | |
|
Maximum Duty Cycle by josh on Fri, 2017-07-14 02:38 |
2 |
by josh Fri, 2017-07-14 20:32 |
VESC6 Beta | |
|
Fault finding on failed VESC by dmcke5 on Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
Third Party Hardware | |
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker on Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
General discussion | |
|
Double the Input voltage, now more rpm at load by martin2day on Tue, 2021-07-20 20:26 |
2 |
by martin2day Sat, 2021-07-31 13:47 |
General discussion | |
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion | |
|
Problems with writing Firmware to the processor by Goex on Wed, 2018-03-28 09:11 |
2 |
by Idoff Tue, 2018-04-17 11:04 |
VESC Firmware | |
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty on Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
General discussion | |
|
Regen question by proget.snc on Thu, 2021-09-02 14:36 |
2 |
by proget.snc Fri, 2021-09-03 11:50 |
General discussion | |
|
vesc disconnected during detection by TonyYuan on Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
VESC Firmware | |
|
Cut off after reaching Max. Duty Cycle by toboli on Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
General discussion | |
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter on Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
General discussion | |
|
Raptor 2 by Phill Dixon on Sat, 2019-09-28 19:35 |
2 |
by Phill Dixon Sun, 2019-09-29 14:39 |
General discussion | |
|
GPIO Pins on VESC? by phils on Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
General discussion | |
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen on Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
General discussion | |
|
Is there a workaround to set regen voltage, not current? by Gsorter on Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
General discussion | |
|
Motor setup (6374-192kv) by solidgeek on Fri, 2017-06-09 23:09 |
2 |
by solidgeek Fri, 2017-06-09 23:20 |
VESC6 Beta |
Pages
