You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Flipsky ESC 6.6 - How to Compile? [fixed] by hoeken on Tue, 2021-08-31 03:33 |
3 |
by alexantosh Wed, 2021-12-01 18:55 |
VESC Firmware | |
throttle & braking weak by bryabee3 on Wed, 2017-08-30 09:56 |
3 |
by frank Mon, 2017-09-18 21:04 |
VESC6 Beta | |
Set McConf with no values --> bootloader erased? by Kakskiv on Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
General discussion | |
Setup parameters for battery in VESC Tool by Ulrich on Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
VESC Tool | |
Why Mosfet and Motor HW temp sensor schematic are different?! by ThierryGTLTS on Sat, 2017-09-09 10:13 |
3 |
by ThierryGTLTS Mon, 2017-09-11 12:50 |
VESC Original Hardware | |
Vesc 6 MKIV ? by mchatain on Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
VESC Original Hardware | |
Sensorless temperature compensation by ESCam on Fri, 2018-12-14 19:38 |
3 |
by Roby_88 Sat, 2023-03-11 17:39 |
Feature Requests | |
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin on Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
General discussion | |
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion | |
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
Serial Interface by dougm on Thu, 2017-08-17 04:33 |
3 |
by Pimousse Sat, 2017-08-19 10:34 |
VESC6 Beta | |
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
speed controller at low RPM by hagoston on Mon, 2021-03-08 13:54 |
3 |
by Elwin Sun, 2021-10-31 13:53 |
General discussion | |
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot on Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
General discussion | |
Limp mode via CAN by totalgeek9224 on Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
Feature Requests | |
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion | |
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
Generator app by arvidb on Sat, 2018-09-22 01:03 |
3 |
by stiganielsen Fri, 2019-09-20 14:29 |
VESC Firmware | |
Mini/micro/nano VESC solutions? by Cham on Mon, 2020-09-21 17:34 |
3 |
by Cham Thu, 2020-09-24 12:15 |
Third Party Hardware |