You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Firmware for 4.xx VESC in new VESC Tool? by sl33py on Wed, 2017-06-28 21:27 |
9 |
by sl33py Fri, 2017-07-14 08:29 |
VESC6 Beta | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
|
The first fraction of braking actually accelerates my board. by defyent on Sun, 2019-09-01 11:36 |
8 |
by s0313045 Mon, 2020-06-08 11:33 |
Third Party Hardware | |
|
ADC and Uart reverse button by vufmihai on Sun, 2020-01-05 22:21 |
8 |
by supertiny808 Mon, 2022-07-11 13:41 |
General discussion | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
VESC Battery Packs by frank on Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
General discussion | |
|
Newbie Help - ADC input by nickyg on Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
General discussion | |
|
Flipsky HC 200A VESC programming to eFoil motor by tylerclark on Wed, 2020-03-11 05:52 |
8 |
by okarbon Tue, 2021-02-23 13:19 |
VESC Firmware | |
|
Step by Step Setup by frank on Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
VESC Tool | |
|
No connection with vesc by Matthieu van Ra... on Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
General discussion | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
Probably first dead VESC SIX by Squad on Tue, 2017-06-27 14:00 |
8 |
by frank Thu, 2017-08-17 22:31 |
VESC6 Beta | |
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor on Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
General discussion | |
|
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool | |
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
|
Is this kogging and jitter in low rpms expected? by Snabelost on Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
General discussion | |
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla on Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
General discussion | |
|
HIGH Voltage (350v-450v) VESC by athlon on Sun, 2018-11-25 18:34 |
8 |
by Artabotak Wed, 2024-11-27 12:30 |
Third Party Hardware | |
|
I need help designing 200v 80a vesc by qwerasdf on Mon, 2021-05-03 17:08 |
8 |
by dylanu Thu, 2022-04-14 06:29 |
Third Party Hardware |
Pages
