You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Trampa boards online store by jrowe on Tue, 2019-04-16 06:28 |
by jrowe Tue, 2019-04-16 06:28 |
VESC Original Hardware | ||
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan on Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
General discussion | |
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston on Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
General discussion | |
|
Trapezoidal Trajectory/Position Control by wewa on Sun, 2018-09-23 11:33 |
4 |
by ncbanse Thu, 2023-04-20 21:26 |
Feature Requests | |
|
Trapezoidal/ s curve trajectory/"Position Mode" RPM control of BLDC motor by Vishwa Brahmaiah on Fri, 2019-05-24 18:22 |
1 |
by jelliesejecta Sat, 2019-09-14 10:31 |
General discussion | |
|
Trasmitter not able to communicate with VESC by Andrea on Thu, 2020-03-26 20:22 |
1 |
by TheFallen Mon, 2020-12-28 16:16 |
VESC Tool | |
|
Travis CI by paltatech on Tue, 2019-01-29 00:57 |
by paltatech Tue, 2019-01-29 00:57 |
VESC Firmware | ||
|
Trouble Detecting ABI Encoder on VESC6/75 by jonathansel on Fri, 2022-10-07 22:34 |
by jonathansel Fri, 2022-10-07 22:34 |
General discussion | ||
|
Trouble Downgrading to Firmware 5.03 by hdfghdfgh on Fri, 2023-03-31 22:10 |
by hdfghdfgh Fri, 2023-03-31 22:10 |
VESC Firmware | ||
|
Trouble downloading the tool by maxhertz on Tue, 2022-01-25 03:12 |
6 |
by frank Sat, 2022-02-05 11:02 |
VESC Tool | |
|
Trouble shooting setup by GeoffGuest on Sat, 2020-10-03 06:12 |
by GeoffGuest Sat, 2020-10-03 06:12 |
VESC Original Hardware | ||
|
Trouble with custom hardware design by Evgeni on Sun, 2022-03-06 21:46 |
4 |
by Evgeni Tue, 2022-03-15 21:20 |
Third Party Hardware | |
|
Trouble with FSESC75200 by Erik on Wed, 2020-10-07 19:09 |
by Erik Tue, 2020-10-13 15:07 |
Third Party Hardware | ||
|
Troubleshooting Newborn VESC by vadicus on Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
Third Party Hardware | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Trying to build a can sniffer for vesc with an esp32 by Duz on Fri, 2024-07-19 19:45 |
by Duz Fri, 2024-07-19 19:45 |
Projects incorporating VESC technology | ||
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo on Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
General discussion | |
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
Trying to upgrade old Enertion FOCBOX Fw 2.18 by jyl087 on Fri, 2024-09-13 16:26 |
by jyl087 Fri, 2024-09-13 17:31 |
Third Party Hardware |
Pages
