You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
FOC Encoder autotune issue by David_Lo on Tue, 2020-01-21 11:54 |
by David_Lo Tue, 2020-01-21 11:54 |
VESC Tool | ||
Hall sensor data is all 0. What do? by Byproduct on Sat, 2023-01-14 14:39 |
by Byproduct Wed, 2023-02-08 11:21 |
VESC Tool | ||
PPM Configuration is Only Working While Connected to VESC Software by kyle45 on Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
VESC Tool | |
Wrong Motor detection values after STM swap dual vesc 6 by Micro on Sun, 2019-08-18 01:59 |
by Micro Sun, 2019-08-18 02:14 |
VESC Tool | ||
Data Loggin Values by BLeaCH on Sat, 2020-04-04 07:37 |
by BLeaCH Sat, 2020-04-04 07:37 |
VESC Tool | ||
PPM Mapping by russell.morris1... on Tue, 2021-09-14 22:38 |
by russell.morris1... Tue, 2021-09-14 22:38 |
VESC Tool | ||
VESC Tool crashes when loading/saving motor/app config by bkyrevolution on Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
VESC Tool | |
FOC detection error " R is 0" by MontPierre on Fri, 2017-09-08 19:52 |
38 |
by danielhugentobler Sat, 2022-01-01 23:13 |
VESC Tool | |
Missing Braking Power in ADC by Silverline on Wed, 2019-06-12 19:48 |
8 |
by positiv Fri, 2020-01-24 14:07 |
VESC Tool | |
Android VESC Tool can not connect to BLE Module by sirAnton on Sun, 2020-08-30 13:40 |
by sirAnton Sun, 2020-08-30 13:40 |
VESC Tool | ||
Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550 by mckenzie.keith on Thu, 2022-01-06 02:24 |
1 |
by mckenzie.keith Thu, 2022-01-06 18:54 |
VESC Tool | |
VESC failure presumably due to current oscillations at high current by rsarver on Wed, 2021-03-24 22:06 |
by rsarver Wed, 2021-03-24 22:06 |
VESC Tool | ||
Vesctool otg by meashman on Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
VESC Tool | |
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
Realtime time axis by Eric on Tue, 2017-09-05 14:29 |
12 |
by hexakopter Mon, 2017-10-23 20:23 |
VESC Tool | |
[SOLVED] Can I use ADC2 for main throttle control? by oschwartz10612 on Wed, 2021-12-01 22:38 |
3 |
by oschwartz10612 Fri, 2021-12-03 05:08 |
VESC Tool | |
Throttle Input reading not changing by niko_la on Fri, 2022-07-22 02:40 |
by niko_la Fri, 2022-07-22 02:40 |
VESC Tool | ||
vesc tool crashing on 29aug19 - website down/link? by ianp on Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
VESC Tool | |
Motor not Spinning Up During Setup Wizard by superjay on Tue, 2021-11-23 07:03 |
4 |
by superjay Wed, 2021-11-24 11:25 |
VESC Tool | |
I dont want that my motorwheel works like generator by Vi1 on Sat, 2024-04-27 14:13 |
by Vi1 Sat, 2024-04-27 14:13 |
VESC Tool |