You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Motor command in log? by carboninfusion on Tue, 2020-08-04 07:58 |
by carboninfusion Tue, 2020-08-04 07:59 |
VESC Tool | ||
Kindly delete - Install problem was resolved on a different computer by RobCat on Tue, 2020-03-17 02:48 |
by RobCat Tue, 2020-03-17 03:03 |
VESC Tool | ||
Get data from VESC on Arduino by jhanvisharma on Wed, 2021-04-07 08:25 |
1 |
by CTSchorsch Wed, 2021-04-07 09:05 |
VESC Tool | |
CAN bus support not enabled in this build of vesc tool? by Tsomo on Fri, 2021-10-01 09:48 |
17 |
by s54mtb Thu, 2023-05-11 20:10 |
VESC Tool | |
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh on Wed, 2023-04-26 16:13 |
by hdfghdfgh Wed, 2023-04-26 16:13 |
VESC Tool | ||
ADC Input Change by alivedom on Thu, 2017-12-14 15:18 |
6 |
by andrecorreia Thu, 2021-04-29 14:44 |
VESC Tool | |
Flipsky nrf51288 by Idoff on Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
VESC Tool | |
RPM increase by Tibor Kalman Za... on Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
VESC Tool | |
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS on Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
VESC Tool | |
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE on Wed, 2020-09-09 03:15 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
VESC Tool | ||
Motor Stuck at 55% Duty Cycle by motion_sickness on Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
VESC Tool | |
Motor not running after applying SINE/COSINE settings by DHOUT on Fri, 2023-01-27 03:32 |
by DHOUT Fri, 2023-01-27 03:32 |
VESC Tool | ||
Motor Values in VESC-Tool 2019 by frank on Wed, 2019-02-27 09:40 |
18 |
by Billy N Fri, 2021-03-26 07:22 |
VESC Tool | |
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
Wrong HW version selected during FW update by babyboi on Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
VESC Tool | |
VESC 4.12 - Current limited at 100A by Laerson on Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
VESC Tool | |
LSM6DS3 gyro ? for balancing by amaussa on Sun, 2020-09-13 12:51 |
1 |
by amaussa Mon, 2020-09-21 17:21 |
VESC Tool | |
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe on Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
VESC Tool | |
Logging set values to csv file by jukawt on Mon, 2021-12-06 14:57 |
by jukawt Mon, 2021-12-06 14:57 |
VESC Tool | ||
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool |