You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Using UART from LabVIEW by hannnes on Tue, 2022-04-05 15:19 |
by hannnes Tue, 2022-04-05 15:19 |
General discussion | ||
AMT 102 Encoder not working properly with VESC by DerpRush on Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
General discussion | |
Burned my VESC 6 MKV. Wrong polarity by okhsunrog on Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
General discussion | |
Pid_Speed is braking despite no brake option by Flyingtux on Thu, 2022-04-07 09:41 |
2 |
by Flyingtux Thu, 2022-04-07 15:49 |
General discussion | |
Remote Control and Bluetooth at same time by Grave on Thu, 2022-04-07 22:03 |
by Grave Fri, 2022-04-08 10:06 |
Third Party Hardware | ||
Add support for dual H3LIS331DL accelerometer by SirPolPol on Fri, 2022-04-08 09:09 |
3 |
by frank Mon, 2022-04-11 09:08 |
Feature Requests | |
Flipsky 75/100 Mosfet short? by Michael Campbell on Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
General discussion | |
Motor compatibility (and power levels) by MrSurly on Tue, 2022-04-12 21:43 |
by MrSurly Tue, 2022-04-12 21:43 |
General discussion | ||
Smart Reverse Minimum Erpm by ZenRides on Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
VESC Tool | |
Flux linkage detection failed by Count1310 on Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
General discussion | |
Hybrid mode in FOC - possible? by Oded Mazor on Tue, 2022-04-12 07:42 |
4 |
by Oded Mazor Wed, 2022-04-13 11:28 |
General discussion | |
I need help designing 200v 80a vesc by qwerasdf on Mon, 2021-05-03 17:08 |
8 |
by dylanu Thu, 2022-04-14 06:29 |
Third Party Hardware | |
Porting to a newer STM32 by TechAUmNu on Wed, 2020-09-16 12:38 |
4 |
by STEPHY AKKARA Thu, 2022-04-14 07:57 |
VESC Firmware | |
Problem with BLDC motor direction and code starting sequence. by masifsr on Fri, 2022-04-15 12:37 |
by masifsr Fri, 2022-04-15 12:37 |
VESC Firmware | ||
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash on Tue, 2020-07-21 16:36 |
6 |
by frank Fri, 2022-04-15 17:31 |
General discussion | |
Control of 4000w bldc motor with hall effect sensors by Abdullah Ajmal on Sat, 2022-04-16 10:14 |
1 |
by frank Sat, 2022-04-16 20:01 |
General discussion | |
Cannot read data over UART by amalbers01 on Sat, 2022-04-16 05:03 |
1 |
by frank Sat, 2022-04-16 20:06 |
VESC Firmware | |
VESC Tool app min hardware requirements by flix on Sat, 2022-04-16 22:13 |
by flix Sat, 2022-04-16 22:13 |
VESC Tool | ||
Servo output CAN Formats by vinci on Mon, 2022-04-18 15:35 |
by vinci Mon, 2022-04-18 15:35 |
General discussion | ||
Design custom VESC 6 Hardware by brightlightbeam on Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
General discussion |