You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
2 Speed ADC control by totalgeek9224 on Mon, 2025-09-22 19:47 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
General discussion | ||
|
Current loop resonance in higher ERPM under Current Mode by ypl on Sat, 2019-07-20 09:34 |
by ypl Sat, 2019-07-20 09:34 |
General discussion | ||
|
Is there a way to deactivate roll to start function FW 5.02 by Philo on Sun, 2021-04-11 13:55 |
by Philo Sun, 2021-04-11 13:58 |
Third Party Hardware | ||
|
100_250_mkiii official release by hugros on Mon, 2023-08-07 15:40 |
by hugros Mon, 2023-08-07 15:40 |
VESC Firmware | ||
|
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests | ||
|
Reverse gear is engaged when power is lost by simDen on Mon, 2024-09-30 13:18 |
by simDen Mon, 2024-09-30 13:18 |
VESC Tool | ||
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 on Sun, 2019-02-17 19:20 |
by Syl2078 Sun, 2019-02-17 19:20 |
General discussion | ||
|
9 by RoopeKuisma on Sun, 2020-05-10 21:58 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
General discussion | ||
|
one motor spinning faster than the other? by jon218white on Mon, 2020-12-14 22:57 |
by jon218white Mon, 2020-12-14 22:57 |
VESC Tool | ||
|
24 Volt LiFePO by Vaxinius on Tue, 2024-09-10 16:34 |
by Vaxinius Tue, 2024-09-10 16:35 |
General discussion | ||
|
Where to order plastic sleeve for VESC by braingame26 on Thu, 2019-02-07 16:34 |
by braingame26 Thu, 2019-02-07 16:34 |
Third Party Hardware | ||
|
External Bluetooth and IMU on CAN-connected VESCs by frankus on Sat, 2022-03-26 19:58 |
by frankus Sat, 2022-03-26 19:58 |
General discussion | ||
|
Backup file by Done on Tue, 2020-07-28 12:08 |
by Done Tue, 2020-07-28 12:08 |
VESC Tool | ||
|
Making master and slave motors communicate both ways by Sis7 on Tue, 2020-07-21 05:58 |
by Sis7 Tue, 2020-07-21 05:58 |
General discussion | ||
|
Flipsky 75100 not running after firmware update by defazioaa on Sat, 2025-03-29 01:33 |
by defazioaa Sat, 2025-03-29 01:33 |
VESC Firmware | ||
|
Using Motor hall sensors as the encoder by Russ g on Wed, 2019-05-08 16:01 |
by Russ g Wed, 2019-05-08 16:01 |
General discussion | ||
|
Hardware limits 3.66 by rumpsvett on Thu, 2020-01-16 19:50 |
by rumpsvett Thu, 2020-01-16 22:31 |
VESC Firmware | ||
|
Position Limits w/ BDC and ABI Encoder by gokulswami on Thu, 2023-04-13 10:43 |
by gokulswami Thu, 2023-04-13 10:43 |
General discussion | ||
|
Problem by C8CHILU on Tue, 2024-06-04 12:15 |
by C8CHILU Tue, 2024-06-04 12:31 |
General discussion | ||
|
Motor detection and calibration using CAN by charan on Tue, 2026-02-03 14:48 |
by charan Tue, 2026-02-03 14:48 |
General discussion |
Pages
