You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550 by mckenzie.keith on Thu, 2022-01-06 02:24 |
1 |
by mckenzie.keith Thu, 2022-01-06 18:54 |
VESC Tool | |
Foc limit at 25v by Thegolfer on Wed, 2020-08-19 18:51 |
1 |
by Thegolfer Wed, 2020-08-19 19:56 |
General discussion | |
Unidentified Part by amit_bhar on Thu, 2021-12-23 23:43 |
1 |
by skyline1970 Fri, 2021-12-24 09:22 |
Third Party Hardware | |
PID control with VESC by Hacker king on Mon, 2018-03-05 20:05 |
1 |
by Danny Bokma Tue, 2018-03-06 06:19 |
General discussion | |
Torque Ramp Rate whilst in FOC by J_W97 on Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
General discussion | |
status message by riku on Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
General discussion | |
Two VESCs with servo-out firmware by _saeed_arabi_ on Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
General discussion | |
ADC throttle lock. by Billy_Wiz on Mon, 2022-10-31 00:57 |
1 |
by vadicus Mon, 2022-10-31 19:51 |
General discussion | |
Controling two motors with Dual FSESC6.6 in two directions by Rafal on Sat, 2021-10-16 13:47 |
1 |
by frank Mon, 2021-10-18 14:43 |
General discussion | |
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
No Option for Master or Slave on SetUp Input? by trickleung91 on Sun, 2019-06-30 09:06 |
1 |
by frank Sun, 2019-07-21 18:46 |
General discussion | |
Motor parameters constantly changing. by Alistair Goodman on Tue, 2022-09-06 15:57 |
1 |
by Alistair Goodman Wed, 2022-09-07 10:04 |
General discussion | |
vesc tool crashing on 29aug19 - website down/link? by ianp on Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
VESC Tool | |
Updating fw by Phill Dixon on Fri, 2018-07-06 19:30 |
1 |
by frank Fri, 2018-07-13 13:19 |
General discussion | |
Problems with flashing firmware to FLIPSKY ESC by xx11xx on Wed, 2019-08-14 18:10 |
1 |
by kinzma Tue, 2019-08-20 07:56 |
VESC Firmware | |
NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K by zippy on Sun, 2021-06-06 16:19 |
1 |
by zippy Sun, 2021-06-06 17:58 |
VESC Tool | |
VESC 75/300 half bridge burns out when I switch to FOC mode by vajasgeri on Thu, 2023-05-04 14:02 |
1 |
by vadicus Fri, 2023-05-05 19:40 |
Third Party Hardware | |
TINY6 by Sojourn on Mon, 2021-05-31 03:20 |
1 |
by TVAVAE Sat, 2021-07-10 00:46 |
Third Party Hardware | |
the keyboard control doesn't work by dmarko16 on Sun, 2021-02-07 15:34 |
1 |
by skyline1970 Sun, 2021-02-07 17:13 |
General discussion | |
MAX40056F as INA240 alternative by Max2 on Sun, 2022-05-08 01:03 |
1 |
by skyline1970 Thu, 2022-11-24 21:43 |
VESC6 Beta |