You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Newbie Help - ADC input by nickyg on Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
General discussion | |
|
ADC and Uart reverse button by vufmihai on Sun, 2020-01-05 22:21 |
8 |
by supertiny808 Mon, 2022-07-11 13:41 |
General discussion | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor on Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
General discussion | |
|
Flipsky HC 200A VESC programming to eFoil motor by tylerclark on Wed, 2020-03-11 05:52 |
8 |
by okarbon Tue, 2021-02-23 13:19 |
VESC Firmware | |
|
No connection with vesc by Matthieu van Ra... on Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
General discussion | |
|
VESC as Generator - Low Output at High Brake Current? by hoeken on Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
General discussion | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla on Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
General discussion | |
|
No UART Output on VESC6 MKIV by uwala on Sun, 2020-10-25 12:13 |
8 |
by tsm Tue, 2021-12-21 15:20 |
VESC Development and Beta Testing | |
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL on Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
VESC Tool | |
|
How to fix VESC killed by over current in serial comm? by 8bit on Sun, 2021-05-16 04:02 |
8 |
by vadicus Fri, 2023-01-13 19:15 |
Third Party Hardware | |
|
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
|
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool | |
|
Step by Step Setup by frank on Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
VESC Tool | |
|
Using dual VESC for Robot Control by Praveen on Sat, 2021-11-13 11:02 |
8 |
by Autocar Tue, 2021-12-07 21:30 |
General discussion | |
|
Rough acceleration - BLDC & FOC by Loose Nickers on Tue, 2020-02-11 07:56 |
9 |
by MC_DIY_Beginner Mon, 2022-05-16 13:34 |
VESC Tool | |
|
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion | |
|
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware |
Pages
