You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Looking for VESC Tuning Help will pay $ by jordan73s on Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
General discussion | |
|
Vesc Tool For Mac by kmfpod on Tue, 2022-06-14 22:06 |
2 |
by nic sandiland Sun, 2025-09-21 18:21 |
VESC Tool | |
|
Ground Housing VESC by T18m26 on Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
VESC Original Hardware | |
|
Can I measure a 1.5 KW AC Servo with VESC Tool by Don_Karlos on Sun, 2024-05-26 21:28 |
2 |
by adilrepas Mon, 2024-08-05 18:54 |
General discussion | |
|
Firmware flash on new born board by matrixgti on Thu, 2020-10-08 20:39 |
2 |
by TechAUmNu Tue, 2020-10-13 10:18 |
Third Party Hardware | |
|
Can I use 12V power supply? by ryde6 on Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
General discussion | |
|
Not able to drive output current by tecmarek on Tue, 2024-12-10 10:49 |
2 |
by Than Thu, 2025-12-18 03:23 |
Third Party Hardware | |
|
Fault Codes by Joe_Lowtech on Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
VESC Tool | |
|
External MPU not working. by PrestoThePirate on Thu, 2020-05-28 15:59 |
2 |
by Neato Sun, 2023-08-06 22:27 |
General discussion | |
|
FOC detection not working, "L=0" by chundri on Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
VESC Tool | |
|
Help setting up a segway in hub motor wheel by tonycowan on Mon, 2021-08-30 19:39 |
2 |
by Pakran Sun, 2021-09-19 15:02 |
General discussion | |
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 on Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
VESC Tool | |
|
long range tunnel for bluetooth module by heiguga on Tue, 2021-03-09 18:03 |
2 |
by CTSchorsch Sun, 2021-03-21 19:23 |
VESC Firmware | |
|
Dual signal on throttle by tmgofer on Mon, 2023-11-20 09:00 |
2 |
by vadicus Thu, 2024-06-27 07:51 |
Feature Requests | |
|
Is switching to reverse and giving a bit of current the same is braking? by sweendog311 on Thu, 2023-10-26 20:53 |
2 |
by onluckyy Thu, 2023-11-02 13:16 |
General discussion | |
|
Inconsistent battery current by Jean Fourcade on Mon, 2020-02-03 06:28 |
2 |
by vadicus Tue, 2020-02-18 20:39 |
General discussion | |
|
Vesctool otg by meashman on Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
VESC Tool | |
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 on Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
Feature Requests | |
|
Support for AMC1301 powered from bootstrap by antonchromjak on Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
Feature Requests | |
|
Type of motors supported by VESC 6 MKIV by Sami Sahli on Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
General discussion |
Pages
