You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
VESC 4.12 problems with FW newer then 3.10 by muchtete on Tue, 2019-01-29 18:37 |
2 |
by GunnarW Sun, 2019-02-24 11:53 |
VESC Firmware | |
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion | |
|
VESC 75/300 current noise / losing sync? by ezonca on Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
VESC Original Hardware | |
|
Timeline and Source Openness by Geordi on Tue, 2017-09-05 13:35 |
2 |
by elux Fri, 2017-09-08 01:58 |
General discussion | |
|
Help i have no idea how it works... by Xtracker133 on Sat, 2022-12-31 14:55 |
2 |
by Xtracker133 Tue, 2023-01-03 22:52 |
General discussion | |
|
Power switch or standby mode by Dillon on Thu, 2017-09-14 16:57 |
2 |
by Dillon Sat, 2017-09-16 22:07 |
VESC6 Beta | |
|
Looking for VESC Tuning Help will pay $ by jordan73s on Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
General discussion | |
|
IMU and RC control by marcotrt on Mon, 2020-02-03 22:47 |
2 |
by zmei116 Fri, 2020-12-04 00:43 |
General discussion | |
|
DIY vesc 75/300 variant power stage problem by motordriver111 on Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
Third Party Hardware | |
|
Vesc Tool For Mac by kmfpod on Tue, 2022-06-14 22:06 |
2 |
by nic sandiland Sun, 2025-09-21 18:21 |
VESC Tool | |
|
Ground Housing VESC by T18m26 on Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
VESC Original Hardware | |
|
Can I measure a 1.5 KW AC Servo with VESC Tool by Don_Karlos on Sun, 2024-05-26 21:28 |
2 |
by adilrepas Mon, 2024-08-05 18:54 |
General discussion | |
|
Can you switch censored to sensor less or HFI by diyRick on Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
General discussion | |
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac on Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
VESC Tool | |
|
Not able to drive output current by tecmarek on Tue, 2024-12-10 10:49 |
2 |
by Than Thu, 2025-12-18 03:23 |
Third Party Hardware | |
|
set current with custom app by sirAnton on Thu, 2017-10-12 12:42 |
2 |
by benjamin Thu, 2017-10-19 21:10 |
VESC Firmware | |
|
Connect PixHawk 4 to FSESC 4.12 by iwdok on Tue, 2021-10-19 11:18 |
2 |
by frank Wed, 2021-12-01 13:38 |
Third Party Hardware | |
|
high speed mode -- 100% PWM duty cycle and over-modulation by RSR on Sun, 2018-06-17 12:21 |
2 |
by frank Mon, 2025-02-24 09:16 |
Feature Requests | |
|
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe on Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
VESC Tool |
Pages
