You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
Previous versions of VESC Tool by Drosselmeier on Fri, 2023-07-14 12:49 |
by Drosselmeier Fri, 2023-07-14 12:49 |
VESC Tool | ||
|
4.12 cooling mod by thewho on Wed, 2019-05-01 18:45 |
by thewho Wed, 2019-05-01 18:45 |
General discussion | ||
|
FSESC 75100 motor problem by anythingstl on Tue, 2024-02-13 17:15 |
by anythingstl Mon, 2024-02-19 19:23 |
General discussion | ||
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller? by avaid on Thu, 2025-05-08 12:57 |
by avaid Tue, 2025-05-13 08:02 |
General discussion | ||
|
HM-10 BLE adapter? by ziumus on Mon, 2019-04-22 00:42 |
by ziumus Mon, 2019-04-22 00:42 |
General discussion | ||
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
|
Remote pairs but motor does not spin after VESC tool use by frunobulax on Fri, 2025-04-11 18:26 |
by frunobulax Fri, 2025-04-11 18:26 |
General discussion | ||
|
VESC PID by nidhirao on Tue, 2019-12-17 13:56 |
by nidhirao Tue, 2019-12-17 13:56 |
VESC Firmware | ||
|
Max eRPM with latest firmware by kubark42 on Fri, 2020-07-17 19:10 |
by kubark42 Fri, 2020-07-17 19:10 |
General discussion | ||
|
Problem with motor startup - only 1/2 of pole positions work in FOC by Knapers on Wed, 2021-03-03 16:51 |
by Knapers Wed, 2021-03-03 17:00 |
General discussion | ||
|
OneWheel Pint Torque by VirtualGrid on Fri, 2024-06-14 03:28 |
by VirtualGrid Fri, 2024-06-14 03:28 |
General discussion | ||
|
dual vesc question by badger1666 on Sun, 2018-10-28 12:59 |
by badger1666 Sun, 2018-10-28 12:59 |
General discussion | ||
|
Android version : ERPM > RPM in RT DATA, a useful refinement by unimotion on Tue, 2020-03-24 10:58 |
by unimotion Tue, 2020-03-24 10:58 |
Feature Requests | ||
|
EBike Bafang M500 mide drive motor: VESC + DIY ESP32 board running Pyhton firmware by yes_wecangogreen on Wed, 2023-04-12 00:43 |
by yes_wecangogreen Tue, 2023-04-25 02:04 |
Projects incorporating VESC technology | ||
|
Electric Mower Blade Speed by moose09876 on Tue, 2024-05-28 20:38 |
by moose09876 Tue, 2024-05-28 20:38 |
Feature Requests | ||
|
Kindly delete - Install problem was resolved on a different computer by RobCat on Tue, 2020-03-17 02:48 |
by RobCat Tue, 2020-03-17 03:03 |
VESC Tool | ||
|
Setup motor foc by Vincent LAMBERT on Thu, 2022-02-03 12:22 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
VESC Tool | ||
|
Flipsky6.6 usb not detected by krom68 on Sat, 2019-02-23 10:21 |
by krom68 Wed, 2019-02-27 19:43 |
Third Party Hardware | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Tool |
Pages
