You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC for small drone (<1kg) by iKrosoft on Wed, 2018-10-03 16:40 |
3 |
by arvidb Thu, 2018-10-04 21:05 |
General discussion | |
|
Wiring two VESCs by neuromancer2701 on Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
General discussion | |
|
Switch two Motor Profiles/Modes (UART) by anli on Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
General discussion | |
|
dual vesc by badger1666 on Fri, 2018-09-21 09:10 |
4 |
by badger1666 Sat, 2018-09-29 15:45 |
General discussion | |
|
Compiling in a different config. by Roger Wolff on Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
General discussion | |
|
Speed control tuning for 500-1000 RPM by vadimz on Sun, 2018-09-02 18:09 |
2 |
by vadimz Sat, 2018-09-15 14:08 |
General discussion | |
|
FAULT_CODE_DRV Motor not spinning by Mightyorc on Sat, 2018-09-15 03:36 |
by Mightyorc Sat, 2018-09-15 03:36 |
General discussion | ||
|
Cut-out at >40A by thewho on Thu, 2018-09-13 20:24 |
by thewho Thu, 2018-09-13 20:24 |
General discussion | ||
|
AS5048A and the AS5047D Problems. by raess on Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
General discussion | |
|
Vesc and Arduino Interface with ppm control???? by ruthvikchanda on Mon, 2018-09-10 12:01 |
by ruthvikchanda Mon, 2018-09-10 12:01 |
General discussion | ||
|
Sudden motor stop by dmcke5 on Wed, 2018-08-15 13:50 |
2 |
by andreas Thu, 2018-09-06 20:48 |
General discussion | |
|
How to erase whole flash with OpenOCD? by Frazatto on Mon, 2018-09-03 14:56 |
1 |
by Frazatto Tue, 2018-09-04 19:33 |
General discussion | |
|
How to read MotorRPM from UART to Arduino by azobe on Thu, 2018-03-08 14:42 |
3 |
by Pimousse Mon, 2018-09-03 14:31 |
General discussion | |
|
What temerpature sensor and how do I use it? by evoheyax on Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
General discussion | |
|
4.12 HK VESC - Static blue LED and no usb Connection, HELP!! by plot1992 on Thu, 2018-08-02 19:01 |
5 |
by Frazatto Tue, 2018-08-28 15:43 |
General discussion | |
|
hall sensor calibration. by Roger Wolff on Mon, 2018-04-16 11:17 |
5 |
by svs Mon, 2018-08-27 13:34 |
General discussion | |
|
Set McConf with no values --> bootloader erased? by Kakskiv on Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
General discussion | |
|
VESC Software Understanding by shubhamt on Wed, 2018-08-22 15:40 |
by shubhamt Wed, 2018-08-22 15:40 |
General discussion | ||
|
Hub motor FOC detection. by Roger Wolff on Tue, 2018-08-21 19:12 |
by Roger Wolff Tue, 2018-08-21 19:12 |
General discussion | ||
|
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion |
Pages
