You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flipsky 75100 Pro V2.0 + Ninebot Max G2 motor: FOC auto-detection failure by Killbot283 » Fri, 2026-06-26 14:49 |
2 |
by nikolaygenov79 Fri, 2026-07-03 13:34 |
|
|
Shunt resistor replacement and too high motor current by lacondro » Mon, 2024-03-25 05:56 |
2 |
by lacondro Wed, 2024-03-27 09:55 |
|
|
wrong amps reading (realtime data) by flez1966 » Wed, 2024-03-27 13:55 |
2 |
by B1996 Tue, 2024-12-03 07:26 |
|
|
compatability assistance by NRGFPV » Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
|
|
Connect PixHawk 4 to FSESC 4.12 by iwdok » Tue, 2021-10-19 11:18 |
2 |
by frank Wed, 2021-12-01 13:38 |
|
|
Firmware flash on new born board by matrixgti » Thu, 2020-10-08 20:39 |
2 |
by TechAUmNu Tue, 2020-10-13 10:18 |
|
|
Unidentified Part by amit_bhar » Thu, 2021-12-23 23:43 |
1 |
by skyline1970 Fri, 2021-12-24 09:22 |
|
|
Custom 75_150 board noise and not synchronized by lacondro » Mon, 2022-08-01 09:06 |
1 |
by lacondro Tue, 2022-08-02 13:26 |
|
|
Chinese board questions. I don't know where to start by seanus4u@gmail.com » Mon, 2022-08-15 02:00 |
1 |
by AngelKillR Wed, 2022-09-28 04:44 |
|
|
Diagnosing FSESC4.20 dead/weird phase (?) by josephduchesne » Sun, 2022-09-18 23:52 |
1 |
by skyline1970 Thu, 2022-11-24 20:23 |
|
|
Flipsky 75200 + Flipsky 85135 12kw only 2kw output by giver » Thu, 2022-10-27 21:00 |
1 |
by skyline1970 Thu, 2022-11-24 20:08 |
|
|
Focbox unity FW Version 5.3 support by theparadoxdoge » Thu, 2022-11-17 06:45 |
1 |
by frank Thu, 2022-11-17 17:56 |
|
|
48V Battery cuts off while doing Motor Wizard by NiZZioN » Sun, 2022-04-24 15:31 |
1 |
by kexbox Fri, 2022-05-06 16:32 |
|
|
FSESC6,6 VESC6 version number. by alexantosh » Mon, 2021-11-22 10:34 |
1 |
by ypl Tue, 2022-02-08 21:54 |
|
|
Does the blue tooth adapter from Flipsky now work with Iphone? by Don124 » Thu, 2022-06-23 07:50 |
1 |
by oskkis Wed, 2022-08-17 18:48 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
84v VESC?? by larsrocket » Sun, 2018-04-01 22:41 |
1 |
by larsrocket Mon, 2018-04-30 19:59 |
|
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde » Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
|
|
SPI encoder on MIN4 by john » Wed, 2018-11-14 11:31 |
1 |
by F4metz Sat, 2019-03-02 14:18 |
|
|
MINI FOC from MakerX by YUTW » Thu, 2019-08-08 11:17 |
1 |
by speed3r Tue, 2019-08-13 10:17 |
|
|
ESC ceases operation after 40 sec ride by dekafive » Sun, 2019-08-25 22:25 |
1 |
by frank Mon, 2019-09-02 10:50 |
|
|
Replacement drv8301 vesc 6.6 by jneumann » Sat, 2020-05-16 06:11 |
1 |
by doomy1986 Sat, 2020-05-16 19:53 |
|
|
VESC for third party Sailboat Motor by Eric Crouch » Sat, 2020-06-06 21:17 |
1 |
by thefallen Mon, 2020-06-08 16:27 |
Log in to post new content in the forum.
