You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 6, astroflight 3215, loosing sync with freewheel by Rouckie » Mon, 2020-05-11 00:22 |
0 |
by Rouckie Mon, 2020-05-11 00:22 |
|
|
Speed Pin from motor into VESC 6+? by dfelz » Tue, 2020-04-07 23:42 |
1 |
by frank Mon, 2020-05-04 14:50 |
|
|
Vesc 6.4 has 80A continuous current. Is that battery or motor? by MaxMaker1 » Mon, 2020-03-02 23:35 |
1 |
by velolac Sun, 2020-03-29 17:51 |
|
|
Bug with bluetooth app connect by zmei116 » Tue, 2020-03-17 13:06 |
0 |
by zmei116 Tue, 2020-03-17 13:06 |
|
|
VESC 4.12 wont connect to pc by stefann » Sun, 2020-03-15 00:42 |
0 |
by stefann Sun, 2020-03-15 00:42 |
|
|
Vesc 75/300 burned by electricfox » Sat, 2020-02-15 22:35 |
8 |
by pf26 Fri, 2020-03-06 09:49 |
|
|
Iron less Axialflux Motor by tobiokanobi » Sat, 2019-03-30 12:11 |
6 |
by kaanozgen Wed, 2020-02-26 11:42 |
|
|
VESC WAND by vitormhenrique » Sun, 2020-02-16 19:04 |
0 |
by vitormhenrique Sun, 2020-02-16 19:26 |
|
|
VESC 100/250 by electricfox » Mon, 2020-01-13 20:23 |
4 |
by vitormhenrique Thu, 2020-02-13 01:12 |
|
|
Power switch on VESCT6+ (MK3) by henry10210 » Thu, 2019-12-26 00:47 |
8 |
by henry10210 Tue, 2020-02-11 15:48 |
|
|
Choosing Motor Encoder for VESC by VRdublove » Fri, 2020-01-24 18:51 |
0 |
by VRdublove Fri, 2020-01-24 21:44 |
|
|
Controlling multiple VESC over SPI by ttufuor » Mon, 2019-11-18 04:37 |
2 |
by Danny Bokma Fri, 2020-01-24 18:29 |
|
|
VESC 75/300 with sin/cos encoder by sajjen » Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
|
|
VESC design specification, manual by velolac » Thu, 2020-01-02 15:54 |
1 |
by velolac Sat, 2020-01-11 00:05 |
|
|
VESC 6 Schematic Question by mendez » Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
|
|
75/300 NRF Pairing by eptv » Sat, 2019-10-12 14:47 |
3 |
by frank Thu, 2019-12-05 11:22 |
|
|
Driving two motors with 75/300 by cmarc » Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
|
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 » Sun, 2019-10-13 14:22 |
0 |
by tahirali1 Sun, 2019-10-13 14:22 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
VESC 75/300 current noise / losing sync? by ezonca » Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
VESC Hardware by eschroff » Thu, 2019-07-25 02:38 |
1 |
by skyline1970 Wed, 2019-07-31 13:35 |
|
|
Programming Vesc 4.12 motor spin only in detection mode by DanieleRA » Sun, 2019-07-28 16:29 |
0 |
by DanieleRA Sun, 2019-07-28 16:29 |
|
|
dual VESC battery current by chris_winkel » Tue, 2019-06-18 15:26 |
0 |
by chris_winkel Tue, 2019-06-18 15:26 |
Log in to post new content in the forum.
