You are here
VESC Firmware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
highspeed motors max erpm? by themotorman » Sun, 2018-12-30 00:50 |
2 |
by TechAUmNu Thu, 2019-01-03 17:25 |
|
|
high side active low and low side active high driver signal setting in firmware. by Spencer.chen » Wed, 2021-12-15 14:00 |
0 |
by Spencer.chen Wed, 2021-12-15 14:04 |
|
|
High Power Configuration with Resolver Feedback by Acable » Sat, 2019-03-23 19:28 |
3 |
by paltatech Wed, 2019-04-03 12:57 |
|
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 » Thu, 2017-10-05 17:21 |
0 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
0 |
by Jaystro16 Sun, 2019-08-04 01:39 |
|
|
Help needed VESC - Update missed? by JUST1975 » Tue, 2024-11-26 11:43 |
1 |
by JUST1975 Tue, 2024-11-26 11:53 |
|
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 » Sun, 2023-02-05 18:00 |
3 |
by mvturnho Wed, 2025-05-14 08:46 |
|
|
help flashing 4.12 with new firmware by adamclarke1985 » Fri, 2020-05-01 02:23 |
2 |
by VESCTroll Fri, 2020-05-29 19:09 |
|
|
HEADING information receiving by Andrej » Fri, 2022-09-23 13:39 |
0 |
by Andrej Fri, 2022-09-23 13:39 |
|
|
Hardware limits 3.66 by rumpsvett » Thu, 2020-01-16 19:50 |
0 |
by rumpsvett Thu, 2020-01-16 22:31 |
|
|
Hard faults in mcpwm_foc.c? by vesc_fault » Thu, 2019-01-03 07:00 |
0 |
by vesc_fault Thu, 2019-01-03 07:20 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
|
Hall effect calibration broken on small motors by felixer » Fri, 2021-05-07 03:43 |
0 |
by felixer Fri, 2021-05-07 03:43 |
|
|
Green LED on older VESC, v4.12? by smith2e7 » Mon, 2021-10-18 17:42 |
0 |
by smith2e7 Mon, 2021-10-18 17:42 |
|
|
Get Current over CAN bus by chriswei » Thu, 2019-05-16 13:57 |
4 |
by spacewalker Mon, 2022-02-21 08:25 |
|
|
Generator app by arvidb » Sat, 2018-09-22 01:03 |
3 |
by stiganielsen Fri, 2019-09-20 14:29 |
|
|
General Question about firmware and software by Dor_Segev » Sat, 2020-03-21 13:59 |
3 |
by Dor_Segev Tue, 2020-03-24 09:32 |
|
|
FW stability by NATUITION » Fri, 2021-06-04 15:35 |
2 |
by berryarreo Wed, 2021-06-30 09:15 |
|
|
Fw 4.01 potential issue by Joeshaw » Sun, 2020-03-01 23:15 |
1 |
by Pimousse Sat, 2020-03-21 13:10 |
|
|
FSESC75200 stopped work after firmware update by julia borisova » Thu, 2022-07-07 15:11 |
1 |
by supertiny808 Mon, 2022-07-11 13:47 |
|
|
FSESC 75100 Pro V2 W/ ALUMINUM by drstein99 » Tue, 2025-08-26 23:02 |
2 |
by CRTZ Wed, 2025-12-17 14:16 |
|
|
FOC_Openloop terminal command via CAN? by Jackl » Mon, 2024-01-15 10:09 |
2 |
by Jackl Sun, 2024-03-17 21:27 |
|
|
Focbox Unity by Remedii » Sat, 2024-06-08 04:23 |
3 |
by Unspoken Fri, 2025-04-18 06:26 |
|
|
Focbox by macglen » Wed, 2024-03-27 22:45 |
1 |
by dpeinado Mon, 2024-04-15 17:51 |
|
|
FOC alignment and startup by nami1216 » Mon, 2020-03-30 10:40 |
1 |
by kaanozgen Tue, 2020-03-31 10:57 |
Log in to post new content in the forum.
