You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Sticky:
Step by Step Setup by frank » Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
|
|
Sticky:
Motor Values in VESC-Tool 2019 by frank » Wed, 2019-02-27 09:40 |
18 |
by Billy N Fri, 2021-03-26 07:22 |
|
|
Sticky:
FOC wizard confusion by Stupidspencer » Mon, 2019-07-08 04:18 |
4 |
by lurch Sun, 2021-10-24 14:46 |
|
|
RPM Limit not working by chinzw » Wed, 2017-09-06 09:29 |
5 |
by ThierryGTLTS Thu, 2017-09-07 11:05 |
|
|
Motor Poles by Enak » Fri, 2017-09-08 00:57 |
1 |
by ThierryGTLTS Fri, 2017-09-08 09:01 |
|
|
HW4.12 with FW 3.27, FOC OK, BLDC problems. by ThierryGTLTS » Thu, 2017-09-07 11:14 |
5 |
by ThierryGTLTS Sat, 2017-09-16 18:45 |
|
|
Motor starting while flasing firmware by RSR » Sun, 2017-09-17 15:31 |
0 |
by RSR Sun, 2017-09-17 15:31 |
|
|
Vesc-Tool Raspbian compatible build by mjc60 » Fri, 2017-09-08 18:20 |
3 |
by RSR Tue, 2017-09-19 11:35 |
|
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
|
Maximum Duty Cycle limit is 95% by shimdidly » Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
|
|
Sampled Data (USB related bugs?) by RSR » Wed, 2017-09-13 10:16 |
6 |
by ThierryGTLTS Thu, 2017-10-12 14:25 |
|
|
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly » Sun, 2017-10-15 00:48 |
0 |
by shimdidly Sun, 2017-10-15 00:48 |
|
|
Change HW after wrong Firmware Update by Hassi » Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
|
|
Realtime time axis by Eric » Tue, 2017-09-05 14:29 |
12 |
by hexakopter Mon, 2017-10-23 20:23 |
|
|
Acceleration Temperature Decrease (Relevant Safety Update) by frank » Sun, 2017-10-29 22:19 |
0 |
by frank Sun, 2017-10-29 22:19 |
|
|
4k monitor problem by nlabs » Wed, 2017-11-01 07:36 |
3 |
by benjamin Fri, 2017-11-03 09:22 |
|
|
Version 0.84, some problems with ADC, see 2nd post please! by ThierryGTLTS » Sun, 2017-10-29 14:11 |
3 |
by ThierryGTLTS Fri, 2017-11-03 16:56 |
|
|
Switch between different modes via remote by Cledus » Sun, 2017-10-22 13:56 |
2 |
by MatwoSvK Tue, 2017-11-07 22:32 |
|
|
Initial Setup wizard fails, HW 4.10 by wdaehn » Tue, 2017-09-12 18:47 |
7 |
by wdaehn Wed, 2017-11-29 14:21 |
|
|
bugreport. Scale useless by Roger Wolff » Wed, 2017-11-29 12:24 |
1 |
by Svenska Svenson Mon, 2017-12-04 07:56 |
|
|
Motor detection failed/ 0 faults by jnweb29 » Sat, 2017-12-23 21:07 |
0 |
by jnweb29 Sat, 2017-12-23 21:07 |
|
|
VESC tool "GUI" issue. by Roger Wolff » Tue, 2018-01-02 15:13 |
2 |
by ThierryGTLTS Wed, 2018-01-10 17:38 |
|
|
Vesc_tool OVER_TEMP_FET by XIII » Thu, 2018-01-11 17:26 |
0 |
by XIII Thu, 2018-01-11 17:26 |
|
|
I have the BLUEZ... Or rather... I don't. by Roger Wolff » Wed, 2018-01-03 16:03 |
6 |
by arvidb Wed, 2018-01-17 14:26 |
|
|
Update 0.87 impossible by vpower » Thu, 2018-01-18 13:17 |
2 |
by arvidb Thu, 2018-01-18 17:07 |
Log in to post new content in the forum.
