You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Sensored FOC not working by Jarson » Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
|
|
Partial throttle input smoothing / jerky control by moose09876 » Thu, 2023-08-10 20:56 |
1 |
by moose09876 Sun, 2023-09-24 19:28 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
|
Looking for 3.01 apk by jsbenson » Sun, 2023-09-10 01:49 |
1 |
by jsbenson Sun, 2023-09-10 04:11 |
|
|
Changing Output Voltage frequency by davbams » Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
|
|
RPM not Working? by ngilchr » Fri, 2023-10-06 16:39 |
1 |
by bayetan Sun, 2023-10-08 23:03 |
|
|
VESC Tool crashes when loading/saving motor/app config by bkyrevolution » Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
|
Expert VESC programmer wanted by SGi » Mon, 2023-10-23 01:59 |
1 |
by electricfox Mon, 2023-10-23 09:12 |
|
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen » Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
|
|
vesc tool crashing on 29aug19 - website down/link? by ianp » Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
|
|
Dev Tools (Scripting) by curt » Mon, 2022-08-22 15:16 |
1 |
by nico01 Thu, 2025-05-29 17:04 |
|
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
|
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik » Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
|
|
Disable bluetooth. by Roger Wolff » Sun, 2018-10-07 17:06 |
1 |
by arvidb Sun, 2018-10-07 17:27 |
|
|
Did I lock myself out of bluetooth connection? by tylerskate » Sat, 2021-05-29 07:18 |
1 |
by Anordil Thu, 2021-08-05 00:06 |
|
|
Hoverboard motor Reverse direction by Silvio Semedo » Sat, 2021-01-16 17:43 |
1 |
by skyline1970 Sun, 2021-02-07 17:32 |
|
|
Sensored acceleration vs sensorless by Mastersam » Tue, 2021-06-01 11:48 |
1 |
by miskuhunor@gmail.com Thu, 2021-09-09 09:41 |
|
|
Erpm / torque setting with remote control, Vesc wand by Lasse » Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
|
|
How to set up 60 degree hall sensors? by ryde6 » Sat, 2021-06-05 12:45 |
1 |
by Jan Jaroš Sat, 2023-06-24 13:47 |
|
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 » Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
|
|
single VESC 6+ controlled by CAN-bus by vinci » Fri, 2021-07-09 15:42 |
1 |
by yuri12 Wed, 2022-02-09 17:23 |
|
|
Firmware 5.2 how to Fast start¡¡¡ by Oscar Lozano Gimenez » Tue, 2021-02-23 10:00 |
1 |
by skyline1970 Fri, 2021-02-26 15:09 |
|
|
Custom GUI by FatsoBatso » Thu, 2021-02-25 16:10 |
1 |
by onid Mon, 2025-01-13 22:00 |
Log in to post new content in the forum.
