You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC CAN_STATUS_1_2_3_4 explained (RPi) by kimpet » Mon, 2019-05-13 12:51 |
3 |
by Jack_Li Tue, 2019-07-30 14:01 |
|
|
FSESC6.6 and Rpi via UART - Understanding the software by gabrielredding » Sat, 2019-07-06 02:50 |
3 |
by abrac Mon, 2019-07-29 14:11 |
|
|
VESC with no working brake button by tavsanist » Sat, 2019-07-27 02:40 |
0 |
by tavsanist Sat, 2019-07-27 02:40 |
|
|
Weird BLDC Current Waveform by thepcman » Thu, 2019-07-25 10:38 |
0 |
by thepcman Thu, 2019-07-25 10:41 |
|
|
No Option for Master or Slave on SetUp Input? by trickleung91 » Sun, 2019-06-30 09:06 |
1 |
by frank Sun, 2019-07-21 18:46 |
|
|
lower power output than expected by mxpro32 » Tue, 2019-06-18 21:38 |
3 |
by frank Sun, 2019-07-21 18:39 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
Efficiency Control by devin » Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
Something about encoder connection by ztwsa007 » Mon, 2019-07-01 13:43 |
1 |
by ztwsa007 Fri, 2019-07-05 03:26 |
|
|
step by step ebike thorttle setup by sindre » Wed, 2019-07-03 17:59 |
0 |
by sindre Wed, 2019-07-03 17:59 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
5V/serial weirdness when using FOC by wihrl » Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
|
|
Low duty cycle issues by nathantarlinton » Tue, 2019-06-25 03:01 |
1 |
by bobfrank Tue, 2019-06-25 03:39 |
|
|
Problem to start bldc in vesc tool vesc-mini4 esc by uav-orion » Wed, 2019-06-12 16:18 |
5 |
by uav-orion Wed, 2019-06-19 21:50 |
|
|
order from Trampa boards by Abricosvw » Mon, 2019-06-17 02:06 |
1 |
by frank Mon, 2019-06-17 17:01 |
|
|
Regenerative braking question and vesc input question by asaf123098 » Sat, 2019-06-15 09:55 |
2 |
by asaf123098 Sun, 2019-06-16 00:23 |
|
|
Difference between maximum current values by Rico » Fri, 2019-06-14 16:06 |
1 |
by frank Sat, 2019-06-15 12:21 |
|
|
Motor refuses to spin after Wizard, VESC 6.6 by Wisdomwagon » Thu, 2019-06-13 16:20 |
1 |
by Wisdomwagon Thu, 2019-06-13 18:54 |
|
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma » Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
|
|
VESC 6 FOC wizard and current limitations. by Bor Zabric » Mon, 2019-06-10 21:12 |
1 |
by TechAUmNu Wed, 2019-06-12 14:42 |
|
|
Sync loss when switching from HALL to sensorless by blezalex » Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
|
|
Step/Dir signals by wall0069 » Sun, 2019-06-09 16:06 |
0 |
by wall0069 Sun, 2019-06-09 16:06 |
|
|
Brake Current Command Adjustments by josh » Fri, 2019-05-17 21:37 |
2 |
by josh Wed, 2019-06-05 17:14 |
|
|
VESC at very low speeds by LudoJ » Wed, 2019-05-15 16:09 |
1 |
by Roger Wolff Sun, 2019-06-02 10:25 |
Log in to post new content in the forum.
