You are here
VESC6 Beta
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Sticky:
MANUAL by frank » Sat, 2017-06-10 00:29 |
2 |
by frank Wed, 2017-06-14 16:46 |
|
|
Sticky:
VESC BETAs HAVE WRONG LABEL PRINTED TO SENSOR PORT by hexakopter » Thu, 2017-06-08 22:49 |
5 |
by frank Thu, 2017-06-22 23:00 |
|
|
Sticky:
VESC Tool for old hardware by benjamin » Fri, 2017-07-07 11:49 |
17 |
by frank Mon, 2017-10-09 15:56 |
|
|
Sticky:
WARNINGs!! What you should not do! by frank » Fri, 2017-06-09 00:55 |
7 |
by frank Wed, 2019-11-06 10:59 |
|
|
Sticky:
First firmware update by benjamin » Fri, 2017-06-09 13:56 |
2 |
by JP Wed, 2022-08-17 11:24 |
|
|
Sticky:
Failures so far and how to prevent them by benjamin » Wed, 2017-07-05 13:07 |
20 |
by Alex Velington Sun, 2023-02-12 22:48 |
|
|
Can-bus by Sanjoy » Tue, 2017-06-06 21:51 |
1 |
by frank Tue, 2017-06-06 22:50 |
|
|
ppm controller questions. [first build] by Jacob Lord » Fri, 2017-06-09 20:44 |
1 |
by frank Fri, 2017-06-09 22:08 |
|
|
Welcome by frank » Fri, 2017-06-02 16:31 |
7 |
by sebaszz Fri, 2017-06-09 22:36 |
|
|
I'm lost! How to get the VESC Tool by Maximilian Scherff » Fri, 2017-06-09 22:19 |
2 |
by Maximilian Scherff Fri, 2017-06-09 22:49 |
|
|
Unable to update firmware using vesc-tool by iPeel » Tue, 2017-06-06 19:55 |
22 |
by Sanjoy Fri, 2017-06-09 23:17 |
|
|
Motor setup (6374-192kv) by solidgeek » Fri, 2017-06-09 23:09 |
2 |
by solidgeek Fri, 2017-06-09 23:20 |
|
|
Connector types and pitch? by iPeel » Tue, 2017-06-06 08:15 |
6 |
by Roger Wolff Sat, 2017-06-10 14:39 |
|
|
First impressions to the new VESC Tool software by hexakopter » Fri, 2017-05-26 21:19 |
10 |
by Roger Wolff Sun, 2017-06-11 06:27 |
|
|
Up and running by Sanjoy » Mon, 2017-06-12 11:01 |
3 |
by frank Mon, 2017-06-12 14:46 |
|
|
VESC CNC case - Feedbacks by Pimousse » Wed, 2017-06-07 17:58 |
19 |
by Necromenz Mon, 2017-06-12 23:44 |
|
|
single 6374 FOC ride log + question on temp cutoff by makevoid » Sun, 2017-06-11 23:48 |
3 |
by makevoid Tue, 2017-06-13 00:24 |
|
|
Mounting points through the PCB by iPeel » Thu, 2017-06-15 16:07 |
3 |
by frank Thu, 2017-06-15 17:53 |
|
|
Windows 10 by Sanjoy » Mon, 2017-06-12 10:54 |
7 |
by benjamin Fri, 2017-06-16 12:09 |
|
|
First impressions to the new VESC HW6.4 by hexakopter » Thu, 2017-06-15 03:08 |
2 |
by hexakopter Fri, 2017-06-16 17:54 |
|
|
Invert motor direction. by Sanjoy » Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
|
|
Timeout brake does not seem to work by Squad » Sat, 2017-06-17 14:55 |
5 |
by benjamin Mon, 2017-06-19 19:52 |
|
|
foc_openloop does not work. by Roger Wolff » Sun, 2017-06-18 14:10 |
4 |
by lizardmech Fri, 2017-06-23 18:32 |
|
|
Remote control that works with the VESC 6 by Oyta » Thu, 2017-06-08 19:33 |
14 |
by fedestanco Fri, 2017-06-23 19:18 |
|
|
Large VESC by lizardmech » Fri, 2017-06-23 19:46 |
0 |
by lizardmech Fri, 2017-06-23 19:46 |
Log in to post new content in the forum.
