You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Custom firmware for DPV by Amirhas on Sun, 2020-11-01 14:36 |
1 |
by CTSchorsch Thu, 2020-11-05 20:42 |
VESC Firmware | |
|
Sensored acceleration vs sensorless by Mastersam on Tue, 2021-06-01 11:48 |
1 |
by miskuhunor@gmail.com Thu, 2021-09-09 09:41 |
VESC Tool | |
|
VESC observer by knuthcomi on Sun, 2021-04-11 02:57 |
1 |
by knuthcomi Wed, 2021-04-14 00:07 |
General discussion | |
|
Wand remote with non-Trampa boards by hans_maier on Fri, 2019-09-20 23:18 |
1 |
by frank Sat, 2019-09-28 21:46 |
General discussion | |
|
KV command in terminal ( how to determine kv of a motor ) by fessyfoo on Sat, 2020-05-09 21:21 |
1 |
by rafeh1 Mon, 2022-08-08 04:31 |
VESC Tool | |
|
Vesc faults when there is load by NIKTEN96 on Sat, 2020-12-12 23:30 |
1 |
by vadicus Mon, 2020-12-14 23:35 |
Third Party Hardware | |
|
Vesc control over CAN by meilutisr on Thu, 2021-07-22 16:12 |
1 |
by meilutisr Fri, 2021-07-23 18:09 |
General discussion | |
|
VESCs rotating the motors at constant RPM on UART control by Pratham701 on Tue, 2021-07-13 10:49 |
1 |
by Indy8976 Wed, 2022-08-24 11:27 |
General discussion | |
|
How to access VESC error codes in the new VESC tool by berno3 on Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
VESC Tool | |
|
Voltage vs Heating ? by marko on Thu, 2019-04-25 21:40 |
1 |
by moto_guy Fri, 2019-04-26 06:02 |
General discussion | |
|
DIY Vesc 6 issues with motor detection by roxes1 on Sun, 2017-11-12 10:15 |
1 |
by roxes1 Sun, 2018-02-11 07:23 |
Third Party Hardware | |
|
esc tester by FatsoBatso on Wed, 2021-02-24 18:05 |
1 |
by skyline1970 Fri, 2021-02-26 14:55 |
General discussion | |
|
Can control Vesc 100/250 by David_1 on Sat, 2022-06-18 01:31 |
1 |
by David_1 Sun, 2022-06-19 19:44 |
General discussion | |
|
Using ABI Encoders by danielw on Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
VESC Original Hardware | |
|
Recording VESC parameters by Alexandru Ciocan on Wed, 2020-03-25 08:44 |
1 |
by Jamie42 Wed, 2020-03-25 12:24 |
General discussion | |
|
Sailboat regen by flydr2 on Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
VESC Tool | |
|
GPDrive as AC current source by jdn2 on Tue, 2019-10-15 14:22 |
1 |
by frank Thu, 2019-10-17 11:14 |
General discussion | |
|
The best and most powerful gimbal on the market using vesc6 for the PRO 360 cameras! by zmei116 on Sun, 2020-05-31 21:56 |
1 |
by zmei116 Sun, 2020-05-31 21:57 |
The VESC-Project | |
|
Battery discharge curve by Madaboutfoiling on Sun, 2023-02-05 08:23 |
1 |
by oangelo Wed, 2023-02-08 00:02 |
General discussion | |
|
How to connect MPU6050 breakout board to VESC 4.12 by klucznik on Sun, 2020-01-26 19:11 |
1 |
by klucznik Sun, 2020-01-26 22:06 |
General discussion |
Pages
