You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware | |
|
Getting RPM data from VESC 4.12 by EmirDns on Wed, 2022-01-05 21:20 |
by EmirDns Wed, 2022-01-05 21:20 |
VESC Original Hardware | ||
|
75/300 R3 and metr.at wird iOS metr App by nice2cu on Sun, 2020-09-13 20:51 |
by nice2cu Sun, 2020-09-13 20:51 |
VESC Original Hardware | ||
|
VESC 6 Plus reseting settings and firmware by granstubbe on Fri, 2020-01-10 18:31 |
2 |
by ozcankosar Fri, 2022-11-25 22:18 |
VESC Original Hardware | |
|
Hub motor e-bike not recognized by olivierskypullc... on Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
VESC Original Hardware | |
|
Bringup, pinouts, general manual... where to find? by kubark42 on Sun, 2021-03-07 03:32 |
7 |
by smith2e7 Tue, 2023-01-24 15:34 |
VESC Original Hardware | |
|
VESC 100/250 won't go full duty cycle by TheBennis on Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
VESC Original Hardware | |
|
VESC 6 Schematic Question by mendez on Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
VESC Original Hardware | |
|
Are the FOC PID values for discrete or continuous time controllers? by ward on Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
VESC Original Hardware | |
|
2 VESC 100/200 single power on switch by tobiokanobi on Wed, 2022-08-31 16:06 |
4 |
by tobiokanobi Mon, 2022-09-05 11:44 |
VESC Original Hardware | |
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis on Fri, 2020-05-22 07:34 |
2 |
by TheFallen Wed, 2020-05-27 08:59 |
VESC Original Hardware | |
|
VESC 6 MK IV circuit question by Simmo1337 on Tue, 2022-08-16 23:10 |
by Simmo1337 Tue, 2022-08-16 23:10 |
VESC Original Hardware | ||
|
Using ABI Encoders by danielw on Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
VESC Original Hardware | |
|
Bug with bluetooth app connect by zmei116 on Tue, 2020-03-17 13:06 |
by zmei116 Tue, 2020-03-17 13:06 |
VESC Original Hardware | ||
|
Trouble shooting setup by GeoffGuest on Sat, 2020-10-03 06:12 |
by GeoffGuest Sat, 2020-10-03 06:12 |
VESC Original Hardware | ||
|
Hall count drift by xachmo on Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
VESC Original Hardware | |
|
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi on Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
VESC Original Hardware | |
|
Speed Pin from motor into VESC 6+? by dfelz on Tue, 2020-04-07 23:42 |
1 |
by frank Mon, 2020-05-04 14:50 |
VESC Original Hardware | |
|
DRV8302 Gate drive limitations by nickw1881 on Sun, 2018-04-29 09:56 |
by nickw1881 Sun, 2018-04-29 09:56 |
VESC Original Hardware | ||
|
Vesc EDU non beta firmware? by Rick van der Sloot on Sat, 2022-10-08 07:50 |
1 |
by frank Mon, 2022-10-10 20:16 |
VESC Original Hardware |
Pages
