You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Using 13s battery on flipsky FSESCs. Is it safe? by Murilo on Thu, 2022-01-27 02:59 |
2 |
by Murilo Thu, 2022-01-27 20:20 |
General discussion | |
|
AS5047 with VESC75/300 by hpb66 on Mon, 2021-11-29 10:11 |
5 |
by canoeman Fri, 2022-01-28 20:17 |
VESC Original Hardware | |
|
Motor cogging by blox11 on Thu, 2022-01-27 03:07 |
6 |
by blox11 Fri, 2022-01-28 21:37 |
General discussion | |
|
Limiting Down hill speed by dbau on Sat, 2022-01-29 06:54 |
by dbau Sat, 2022-01-29 09:19 |
General discussion | ||
|
Loss of control during regen by mckenzie.keith on Fri, 2022-01-28 02:42 |
3 |
by frank Sat, 2022-01-29 10:34 |
VESC Firmware | |
|
Golden Motor HPM48-5000, reconciling winding R & L values by j.konrad on Sat, 2022-01-15 22:09 |
24 |
by j.konrad Mon, 2022-01-31 15:15 |
General discussion | |
|
Have i bricked my flipsky FSESC 4.20? by olletj on Sat, 2022-01-22 18:03 |
2 |
by olletj Mon, 2022-01-31 21:18 |
Third Party Hardware | |
|
RL measurement incorrect with factor 2/3? (Page: 1, 2)
by Elwin on Sun, 2021-10-03 00:33 |
59 |
by Elwin Mon, 2022-01-31 23:22 |
General discussion | |
|
Vesc - UAVCAN - Pixhawk by dbau on Tue, 2022-02-01 07:43 |
1 |
by dbau Tue, 2022-02-01 07:57 |
General discussion | |
|
NRF connection error by Denn on Wed, 2022-02-02 11:17 |
by Denn Wed, 2022-02-02 11:17 |
VESC Tool | ||
|
Mid-drive ebikes? by Zoltan on Fri, 2022-01-28 16:37 |
3 |
by frank Thu, 2022-02-03 08:51 |
General discussion | |
|
Arduino PPM disable regen by jeengerbread on Thu, 2022-02-03 00:09 |
1 |
by frank Thu, 2022-02-03 09:01 |
General discussion | |
|
Setup motor foc by Vincent LAMBERT on Thu, 2022-02-03 12:22 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
VESC Tool | ||
|
VESC with propeller, not reaching max performance by ogent on Tue, 2022-02-01 16:31 |
8 |
by ogent Thu, 2022-02-03 14:54 |
VESC Firmware | |
|
Problems with UART communication via Arduino UNO by Michael Hamm on Fri, 2022-02-04 13:29 |
by Michael Hamm Fri, 2022-02-04 13:29 |
General discussion | ||
|
Trouble downloading the tool by maxhertz on Tue, 2022-01-25 03:12 |
6 |
by frank Sat, 2022-02-05 11:02 |
VESC Tool | |
|
Remote not receiving telemetry data by jasson on Sun, 2022-02-06 04:21 |
2 |
by jasson Sun, 2022-02-06 05:56 |
General discussion | |
|
CAN eRPM report by alxsfrm on Mon, 2022-02-07 11:01 |
by alxsfrm Mon, 2022-02-07 11:01 |
General discussion | ||
|
Sending RPM via UART to STM32 by EmirDns on Sat, 2022-01-08 11:00 |
3 |
by EmirDns Mon, 2022-02-07 17:38 |
General discussion | |
|
VESC6 MK5 CAN communication does not work by Andy Moon on Tue, 2022-02-08 01:59 |
by Andy Moon Tue, 2022-02-08 01:59 |
VESC Original Hardware |
Pages
