You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Can not run again after run perfectly !! Pls help by Streetstar69 on Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
General discussion | |
|
Wand firmware 1.3 by peacue on Mon, 2021-11-22 09:59 |
1 |
by frank Mon, 2021-11-22 12:56 |
VESC Firmware | |
|
vesc tool page not opening by bsissell on Sun, 2021-11-21 20:46 |
1 |
by velolac Sun, 2021-11-21 22:13 |
General discussion | |
|
Step-by-step manual or overview for VESC + Arduino control by vretier on Sat, 2021-11-20 21:39 |
1 |
by skyline1970 Sun, 2021-11-21 08:33 |
General discussion | |
|
Hall sensor problems by Traceo on Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
VESC Tool | |
|
Two VESCs, two three-phase windings, one motor stator by kubark42 on Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
General discussion | |
|
Flipsky FSESC 4.12 Bluetooth over mini USB? by blaz.ferlic on Fri, 2021-11-19 10:18 |
3 |
by lurch Fri, 2021-11-19 14:00 |
Third Party Hardware | |
|
Unofficial VESC Discord server by kubark42 on Tue, 2021-11-16 16:07 |
by kubark42 Fri, 2021-11-19 03:12 |
General discussion | ||
|
EDS Files for Somachine or Codesys by philippe faul on Sun, 2021-09-19 18:00 |
1 |
by Tecnoveritas Thu, 2021-11-18 17:06 |
General discussion | |
|
UART Arduino Monitor by arranto12 on Thu, 2021-11-18 00:24 |
by arranto12 Thu, 2021-11-18 00:24 |
General discussion | ||
|
Control System of VESC by mm_iem on Wed, 2021-08-25 14:52 |
2 |
by kubark42 Wed, 2021-11-17 16:59 |
VESC Firmware | |
|
Experience with QS120 IPM motor? by marvinrau on Mon, 2021-05-31 14:03 |
12 |
by pe Tue, 2021-11-16 18:20 |
General discussion | |
|
large hub motors by Frankey on Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
General discussion | |
|
Using a cadence sensor or torque sensor as a throttle with a VESC 6 Trampa Boards by UgoLegendre on Tue, 2021-11-16 11:48 |
1 |
by lurch Tue, 2021-11-16 13:02 |
General discussion | |
|
Urgent VESC Firmware Issue by D1200 on Tue, 2021-11-16 02:32 |
2 |
by frank Tue, 2021-11-16 09:50 |
VESC Firmware | |
|
Braking noisy on Hoverboards hubs . by lurch on Mon, 2021-11-08 15:59 |
2 |
by lurch Mon, 2021-11-15 21:35 |
General discussion | |
|
Single Flipsky FSESC 6.6 getting started and IMU data by alexantosh on Wed, 2021-04-07 12:32 |
by alexantosh Mon, 2021-11-15 13:10 |
Third Party Hardware | ||
|
Motor Stuck at 55% Duty Cycle by motion_sickness on Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
VESC Tool | |
|
ADC control not linear or smooth by arranto12 on Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
General discussion | |
|
Overvoltage Error during setup by arranto12 on Mon, 2021-11-08 23:22 |
2 |
by skyline1970 Sat, 2021-11-13 18:18 |
General discussion |
Pages
