You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
Dual Vesc reading second wheel RPM by rdavenport3 on Tue, 2022-05-03 15:32 |
by rdavenport3 Tue, 2022-05-03 15:32 |
VESC Firmware | ||
|
CAN Analyzer by min on Tue, 2022-05-03 10:38 |
by min Tue, 2022-05-03 10:38 |
General discussion | ||
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion | |
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi on Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
VESC Original Hardware | |
|
VESC output current decreasing in time by isso777 on Sat, 2022-04-30 14:59 |
5 |
by isso777 Mon, 2022-05-02 17:30 |
General discussion | |
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty on Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
General discussion | |
|
VESC Encoder connected to 12v by yanting Liu on Fri, 2022-04-29 07:53 |
1 |
by frank Sat, 2022-04-30 14:24 |
VESC Original Hardware | |
|
Firmware by Phill Dixon on Mon, 2022-04-25 15:29 |
7 |
by frank Sat, 2022-04-30 14:21 |
General discussion | |
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 on Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
VESC Tool | |
|
Control singular VESC using CAN-BUS and Arduino by Cam on Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
General discussion | |
|
Wand (and app) not pairing by Jonny254 on Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
General discussion | |
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
|
VESC Tool speed control overshoot by PKmita on Tue, 2022-04-26 16:05 |
by PKmita Tue, 2022-04-26 16:12 |
VESC Tool | ||
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi on Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
VESC Tool | |
|
Brake hiccup by Phill Dixon on Wed, 2022-03-30 18:23 |
23 |
by Phill Dixon Mon, 2022-04-25 17:45 |
General discussion | |
|
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi on Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
VESC Original Hardware | |
|
Lisp scripting questions/suggestions/remarks by Gatze on Sun, 2022-04-24 12:13 |
by Gatze Sun, 2022-04-24 13:00 |
VESC Tool | ||
|
App development and Debug by dpeinado on Fri, 2022-04-01 13:22 |
1 |
by Gatze Sun, 2022-04-24 00:15 |
VESC Firmware | |
|
how to download v5.03 firmware? by barncat08 on Wed, 2022-01-26 18:35 |
4 |
by Gatze Sat, 2022-04-23 11:48 |
VESC Firmware |
Pages
