You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Torque Ramp Rate whilst in FOC by J_W97 on Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
General discussion | |
|
VESC HD60T CAN DUTY CYCLE CONTROL by v1n23nt on Thu, 2022-02-17 09:39 |
2 |
by v1n23nt Mon, 2022-03-14 16:54 |
General discussion | |
|
Does VESC reduce/disable regen braking based on battery voltage? by rorosaurus on Tue, 2020-08-11 23:20 |
11 |
by J_W97 Mon, 2022-03-14 14:43 |
General discussion | |
|
Powering a Custom Motor With Large Air Gap by magma on Mon, 2022-01-24 23:38 |
1 |
by skyline1970 Mon, 2022-03-14 09:56 |
General discussion | |
|
Controlling a custom made RC Vehicle by Skaaly on Sat, 2022-03-05 12:56 |
1 |
by skyline1970 Mon, 2022-03-14 09:16 |
General discussion | |
|
Emergency Brake. by Solid_37 on Fri, 2020-07-03 22:43 |
3 |
by skyline1970 Mon, 2022-03-14 08:53 |
Feature Requests | |
|
Cannot downgrade from 5.03 to 5.02 by kallep on Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
General discussion | |
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion | ||
|
Upgrade the Bootloader? by erikfed on Tue, 2022-03-08 20:32 |
by erikfed Tue, 2022-03-08 20:32 |
VESC Tool | ||
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 14:19 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
General discussion | ||
|
VESC firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 13:25 |
by Maciejwarloch Tue, 2022-03-08 13:25 |
VESC Firmware | ||
|
Flipsky 75100 controller not producing the same amount of power as esc controller at same current by Ashton on Mon, 2021-12-06 21:18 |
2 |
by Liam Li Sun, 2022-03-06 20:31 |
General discussion | |
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin on Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
General discussion | |
|
How to read the CAN message with CAN anlayzer by yuri12 on Thu, 2022-03-03 18:21 |
by yuri12 Thu, 2022-03-03 18:21 |
VESC Tool | ||
|
Where to find codelines for speed and position control structure by kianK on Tue, 2022-03-01 15:25 |
by kianK Thu, 2022-03-03 12:23 |
VESC Firmware | ||
|
VESC100/250; RPM Pulse input; antispark precharge by tobiokanobi on Mon, 2022-02-28 11:56 |
7 |
by tobiokanobi Thu, 2022-03-03 11:22 |
General discussion | |
|
Best Throttle and break level by ardillolambo on Wed, 2022-03-02 18:29 |
by ardillolambo Wed, 2022-03-02 18:29 |
General discussion | ||
|
Axial Flux motor control mode by ardillolambo on Wed, 2022-03-02 13:59 |
4 |
by ardillolambo Wed, 2022-03-02 18:25 |
VESC Original Hardware | |
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 on Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
General discussion | |
|
VCC-GND short by caliber interconnect on Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
VESC Original Hardware |
Pages
