You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
No UART Output on VESC6 MKIV by uwala on Sun, 2020-10-25 12:13 |
8 |
by tsm Tue, 2021-12-21 15:20 |
VESC Development and Beta Testing | |
|
Additional Status Messages by louisgcr on Tue, 2021-12-21 08:04 |
by louisgcr Tue, 2021-12-21 08:04 |
General discussion | ||
|
Tenka esc in need of a reliable vesc tool by Vincent Gervais on Tue, 2021-12-21 00:48 |
by Vincent Gervais Tue, 2021-12-21 00:48 |
Third Party Hardware | ||
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
Flashing custom code for 100/250 bricked the board by pe on Tue, 2021-11-16 14:14 |
6 |
by kubark42 Fri, 2021-12-17 16:37 |
VESC Development and Beta Testing | |
|
LoRa Support by CTSchorsch on Fri, 2021-12-17 13:59 |
by CTSchorsch Fri, 2021-12-17 13:59 |
Third Party Hardware | ||
|
Vesc Max current 90A Vs ESC Max current 135A? by ScootScoot on Tue, 2021-12-14 13:00 |
5 |
by Markula Thu, 2021-12-16 20:42 |
General discussion | |
|
75 / 300 vesc by craig w on Thu, 2021-12-16 03:36 |
1 |
by electricfox Thu, 2021-12-16 15:29 |
General discussion | |
|
When 100250 is not enough by eptv on Sat, 2021-12-11 14:38 |
10 |
by eptv Wed, 2021-12-15 20:53 |
VESC Original Hardware | |
|
(CLOSED)Custom FW based on beta "could not deserialize" by pe on Wed, 2021-12-15 11:48 |
by pe Wed, 2021-12-15 15:18 |
VESC Development and Beta Testing | ||
|
high side active low and low side active high driver signal setting in firmware. by Spencer.chen on Wed, 2021-12-15 14:00 |
by Spencer.chen Wed, 2021-12-15 14:04 |
VESC Firmware | ||
|
Change maximum allowed input voltage by CTSchorsch on Mon, 2021-12-13 21:37 |
2 |
by CTSchorsch Tue, 2021-12-14 21:47 |
Third Party Hardware | |
|
Current In vs Current Motor by hacksmithCabe on Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
VESC Tool | |
|
Newbie Help - ADC input by nickyg on Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
General discussion | |
|
App. settings: "Enable servo output on PPM-port when PPM-app is disabled." option by alexantosh on Fri, 2021-12-10 09:46 |
by alexantosh Fri, 2021-12-10 09:46 |
VESC Tool | ||
|
Weird behavior when trying to do position control with the AS5047 encoders by geoporus on Thu, 2021-11-11 18:41 |
6 |
by svs Fri, 2021-12-10 04:42 |
General discussion | |
|
Vesc-tool TCP Connection by nlabs on Fri, 2017-12-08 02:30 |
1 |
by milesf Fri, 2021-12-10 03:40 |
VESC Tool | |
|
Motor control by ptss37 on Wed, 2021-12-08 06:52 |
5 |
by ptss37 Fri, 2021-12-10 03:24 |
VESC Tool | |
|
Axial Flow Pump Project by design@imsltd.co.nz on Thu, 2021-12-09 02:05 |
2 |
by design@imsltd.co.nz Fri, 2021-12-10 01:51 |
General discussion | |
|
VESC HD60T discontinued? by RickBoerma on Thu, 2021-12-02 15:58 |
3 |
by RickBoerma Wed, 2021-12-08 12:56 |
General discussion |
Pages
