You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies on Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
VESC Tool | |
|
about VESC6.4 how to connect to tool? by h1989 on Tue, 2024-11-05 16:40 |
by h1989 Tue, 2024-11-05 16:40 |
VESC Firmware | ||
|
Rough Stutter when taking off (48V 750w 75100 Pro v2) by ahagie on Mon, 2024-11-04 01:21 |
by ahagie Mon, 2024-11-04 01:21 |
VESC Tool | ||
|
Controller just shuts off by Stock88 on Sun, 2024-11-03 03:49 |
1 |
by electricfox Sun, 2024-11-03 09:08 |
General discussion | |
|
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 on Thu, 2019-05-02 09:57 |
27 |
by Stock88 Sun, 2024-11-03 04:02 |
VESC Tool | |
|
Questions regarding adc1/2 whilst using one thumb joystick. by Ben26 on Wed, 2024-10-30 12:48 |
3 |
by Ben26 Sat, 2024-11-02 22:19 |
General discussion | |
|
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
VESC Tool | |
|
Flipsky 75200 ALU not booting up by Metastasis on Wed, 2023-09-20 15:45 |
2 |
by B1996 Mon, 2024-10-28 22:06 |
VESC Firmware | |
|
Vesc Tool 6.02 compiling Error on Ubuntu (res_fw.qrc) by Gos1 on Wed, 2023-06-21 17:23 |
4 |
by rafeh1 Sun, 2024-10-27 07:54 |
VESC Tool | |
|
lispBM on VESC for special algorithm by Fusion on Fri, 2024-10-25 11:34 |
4 |
by Fusion Sat, 2024-10-26 17:00 |
General discussion | |
|
Isolated CANbus / CAN by shener on Wed, 2024-10-23 15:15 |
1 |
by Markula Thu, 2024-10-24 22:19 |
General discussion | |
|
No sensers by Phill Dixon on Thu, 2024-10-24 18:58 |
by Phill Dixon Thu, 2024-10-24 18:58 |
General discussion | ||
|
Phase voltage sensor plausibility check by tecmarek on Thu, 2024-10-24 14:17 |
by tecmarek Thu, 2024-10-24 14:24 |
VESC Firmware | ||
|
what is this part for by ynoo443 on Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
General discussion | |
|
How to setup my VESC with AD2S1205 by Vlahosthomas on Tue, 2024-10-22 10:33 |
by Vlahosthomas Tue, 2024-10-22 10:36 |
General discussion | ||
|
Hall Sensors Not Detected by leymane on Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
General discussion | |
|
Do All Vescs Suck? by Zeebybaby on Sun, 2024-10-20 20:33 |
by Zeebybaby Sun, 2024-10-20 20:33 |
General discussion | ||
|
Available connectors by nopf on Wed, 2024-09-18 09:33 |
4 |
by tobiokanobi Sun, 2024-10-20 17:38 |
VESC Original Hardware | |
|
Disable wrong FET temperature sensors by Flo98 on Sat, 2024-10-19 17:49 |
by Flo98 Sat, 2024-10-19 17:54 |
General discussion | ||
|
VESC setup question for a motorised rope ascender. by Ben26 on Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
General discussion |
Pages
