You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Custom-made VESC PCB: High current sensor offset/Overcurrent fault during motor detection, possible hardware/firmware mismatch by Chinmay Mulgund on Mon, 2025-10-13 13:56 |
by Chinmay Mulgund Mon, 2025-10-13 14:02 |
General discussion | ||
|
Trying to run a refrigerant compressor's BLDC with VESC by logansheaf on Wed, 2025-01-29 02:01 |
2 |
by logansheaf Wed, 2025-01-29 23:23 |
General discussion | |
|
VESC 6 motor setup: Resistance measurement jumps by thomasjfox on Mon, 2017-10-09 20:42 |
2 |
by thomasjfox Sat, 2017-10-28 21:57 |
General discussion | |
|
VESC crashes on Servo output by AutonomousDrifting on Fri, 2021-02-05 13:25 |
7 |
by dawgs Sat, 2025-04-19 12:40 |
General discussion | |
|
Which to believe, manufacturer inductance spec or VESC autodetection? by kubark42 on Wed, 2021-09-29 15:59 |
3 |
by kubark42 Fri, 2021-10-22 20:01 |
General discussion | |
|
How is Motor Temperature measured? by shimdidly on Mon, 2017-10-02 07:52 |
4 |
by drummerboy5408 Thu, 2022-05-05 05:06 |
General discussion | |
|
[OT] Increase torque on DC brush motor by Riccio on Mon, 2022-03-28 19:32 |
2 |
by Riccio Tue, 2022-03-29 09:18 |
General discussion | |
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake on Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
General discussion | |
|
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus on Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
General discussion | |
|
Disable throttle while braking by rl_19 on Sat, 2022-03-19 00:05 |
7 |
by flez1966 Thu, 2024-03-21 09:41 |
General discussion | |
|
VESC Logo by beachbrojoe on Thu, 2022-12-08 19:37 |
1 |
by frank Fri, 2022-12-09 14:24 |
General discussion | |
|
Controller (VESC 6 based) dont like small motor by matrixgti on Mon, 2024-01-29 21:27 |
by matrixgti Fri, 2024-02-23 15:37 |
General discussion | ||
|
VESC in-air startup failure by jschall on Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
General discussion | |
|
Help calibrating a hub motor by Tin_Man_0 on Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
General discussion | |
|
ADC control issue by dsuresh on Fri, 2021-03-05 18:21 |
3 |
by dsuresh Wed, 2021-03-10 19:45 |
General discussion | |
|
vesc tool page not opening by bsissell on Sun, 2021-11-21 20:46 |
1 |
by velolac Sun, 2021-11-21 22:13 |
General discussion | |
|
New to electric skateboards - Can't seem to get FSESC set up properly by iguanahotsauce on Sun, 2020-07-12 06:11 |
1 |
by transcendStaticMode Tue, 2020-07-14 07:56 |
General discussion | |
|
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
|
Motor Controller Recommendations - 84V max - 50A Continuous by dylanu on Thu, 2021-11-11 22:54 |
5 |
by mikael Sat, 2023-09-30 01:46 |
General discussion |
Pages
