You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Switching Frequency and current loop speed by bobfrank on Tue, 2019-04-23 10:34 |
2 |
by jerome Wed, 2019-05-08 18:48 |
VESC Firmware | |
|
Switching frequency data by petertaylor on Thu, 2018-11-08 00:53 |
4 |
by petertaylor Tue, 2018-12-25 20:28 |
VESC Firmware | |
|
Switching frequency factor 2 lower by Elwin on Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
General discussion | |
|
switching power supply by MagicKey on Tue, 2023-01-17 04:01 |
2 |
by vadicus Fri, 2023-06-23 22:59 |
General discussion | |
|
Sync loss when switching from HALL to sensorless by blezalex on Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
General discussion | |
|
Synchronizing multiple motors before mechanically locking together by hockinsk on Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
General discussion | |
|
Tachometer VS RPM by Davideo on Mon, 2018-02-05 03:17 |
2 |
by Davideo Tue, 2018-02-06 00:37 |
General discussion | |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp on Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
VESC Tool | |
|
Target VESC has no space to be flashed with ST-Link by Thi4g0tk on Sun, 2021-03-28 14:50 |
by Thi4g0tk Sun, 2021-03-28 14:50 |
Third Party Hardware | ||
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 on Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
General discussion | |
|
temp motor by emmaanuel on Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
VESC Firmware | |
|
temperature compensation make sense？ by alexshen2012 on Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
General discussion | |
|
Temperature Sensor Dallas DS18B20 by tobiokanobi on Tue, 2022-06-07 10:07 |
2 |
by tobiokanobi Wed, 2022-06-08 15:25 |
VESC Original Hardware | |
|
Tenka esc in need of a reliable vesc tool by Vincent Gervais on Tue, 2021-12-21 00:48 |
by Vincent Gervais Tue, 2021-12-21 00:48 |
Third Party Hardware | ||
|
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
The best and most powerful gimbal on the market using vesc6 for the PRO 360 cameras! by zmei116 on Sun, 2020-05-31 21:56 |
1 |
by zmei116 Sun, 2020-05-31 21:57 |
The VESC-Project | |
|
The connected VESC has test firmware, and this is not a test build of VESC Tool. You should update the firmware urgently, as thi by Thomas W Donohue on Sat, 2021-07-17 14:26 |
3 |
by frank Tue, 2021-10-12 20:47 |
VESC Firmware | |
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Tool | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Firmware |
Pages
