You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Autonomous Drifting Research Project by AutonomousDrifting on Fri, 2020-10-30 13:05 |
1 |
by AutonomousDrifting Tue, 2022-04-19 23:21 |
General discussion | |
Max thread rate for simple app? by clazarowitz on Wed, 2022-04-20 04:34 |
by clazarowitz Wed, 2022-04-20 04:34 |
VESC Firmware | ||
Vesc is not turning on by asnamp on Wed, 2022-04-20 09:30 |
1 |
by canoeman Wed, 2022-04-20 15:44 |
General discussion | |
Multiple VESCs on the same battery by Riccio on Wed, 2022-04-20 22:09 |
by Riccio Wed, 2022-04-20 22:09 |
General discussion | ||
Mosfet Discussion by WalterWitt on Mon, 2022-04-18 20:38 |
3 |
by vadicus Thu, 2022-04-21 00:01 |
Third Party Hardware | |
VESC is not working in ADC mode by asnamp on Wed, 2022-04-20 09:21 |
by asnamp Thu, 2022-04-21 20:11 |
General discussion | ||
VESC is not working in ADC mode by asnamp on Thu, 2022-04-21 06:53 |
2 |
by asnamp Fri, 2022-04-22 06:50 |
General discussion | |
Bluetooth module in VESC 75/300 by Hermann Schnaeuzle on Fri, 2022-04-22 17:55 |
by Hermann Schnaeuzle Fri, 2022-04-22 17:55 |
General discussion | ||
how to download v5.03 firmware? by barncat08 on Wed, 2022-01-26 18:35 |
4 |
by Gatze Sat, 2022-04-23 11:48 |
VESC Firmware | |
App development and Debug by dpeinado on Fri, 2022-04-01 13:22 |
1 |
by Gatze Sun, 2022-04-24 00:15 |
VESC Firmware | |
Lisp scripting questions/suggestions/remarks by Gatze on Sun, 2022-04-24 12:13 |
by Gatze Sun, 2022-04-24 13:00 |
VESC Tool | ||
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi on Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
VESC Original Hardware | |
Brake hiccup by Phill Dixon on Wed, 2022-03-30 18:23 |
23 |
by Phill Dixon Mon, 2022-04-25 17:45 |
General discussion | |
experiment tab rpm ramp up and dual separate motor control by tobiokanobi on Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
VESC Tool | |
VESC Tool speed control overshoot by PKmita on Tue, 2022-04-26 16:05 |
by PKmita Tue, 2022-04-26 16:12 |
VESC Tool | ||
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
position hold below specific duty cycle by lacondro on Wed, 2022-04-27 04:41 |
1 |
by lacondro Wed, 2022-04-27 10:44 |
VESC Firmware | |
Wand (and app) not pairing by Jonny254 on Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
General discussion | |
Control singular VESC using CAN-BUS and Arduino by Cam on Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
General discussion | |
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 on Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
VESC Tool |