You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
HALL-FOC---don't understand the mcpwm_foc_hall_detect() function by ConnerL on Wed, 2021-01-06 12:33 |
2 |
by ConnerL Tue, 2021-01-12 02:55 |
General discussion | |
|
ADC out of bounds voltage still maps?! by Matt6288 on Tue, 2021-01-12 02:27 |
by Matt6288 Tue, 2021-01-12 02:27 |
Feature Requests | ||
|
Unable to enable Servo Out on VESC 6 Mk5 by kangalow on Thu, 2021-01-07 20:26 |
1 |
by kangalow Mon, 2021-01-11 23:15 |
VESC Firmware | |
|
VESC Hardware Design For 4 in 1 Quadcopter ESC Board? by aklimaj on Wed, 2021-01-06 22:55 |
2 |
by TheFallen Mon, 2021-01-11 08:38 |
General discussion | |
|
benjamin, New feature please 1. Lock up Profile selection in App. with Password and add RFID reader. by justinlinh on Sat, 2020-07-11 00:08 |
1 |
by Solid_37 Sun, 2021-01-10 23:40 |
Feature Requests | |
|
Motors with known valid configurations by doctarr on Fri, 2021-01-01 14:28 |
4 |
by doctarr Sat, 2021-01-09 14:44 |
Third Party Hardware | |
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:45 |
1 |
by rosemery2511 Tue, 2021-01-05 22:41 |
General discussion | |
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
AS5047 Encoder with VESC 4.20 by rctestflight on Mon, 2020-09-21 19:55 |
1 |
by aparanjpe Sun, 2021-01-03 17:45 |
General discussion | |
|
Why not using interrupt for Hall signal detection? by kuan on Sun, 2021-01-03 09:51 |
by kuan Sun, 2021-01-03 09:51 |
General discussion | ||
|
Ayuda configurar vesc tool by julitosanse on Sat, 2021-01-02 13:24 |
by julitosanse Sat, 2021-01-02 13:24 |
General discussion | ||
|
How do I compile the VESC Tool? by ipbyrne on Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
VESC Tool | |
|
Cannot detect VESC with built-in NRF24 from VESC Tool (Android) by fdumi on Wed, 2020-12-30 11:57 |
by fdumi Wed, 2020-12-30 19:00 |
VESC Firmware | ||
|
compatability assistance by NRGFPV on Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
Third Party Hardware | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Where to find CAN protocol documentation? by doctarr on Tue, 2020-12-29 15:33 |
by doctarr Tue, 2020-12-29 15:33 |
General discussion | ||
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
Trasmitter not able to communicate with VESC by Andrea on Thu, 2020-03-26 20:22 |
1 |
by TheFallen Mon, 2020-12-28 16:16 |
VESC Tool | |
|
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 on Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
VESC Original Hardware | |
|
FSESC 4.12 oscillating and making noise by hichemhlm on Sun, 2020-03-29 13:33 |
1 |
by hichemhlm Sun, 2020-12-27 12:19 |
General discussion |
Pages
