You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Vesc 100/250 for unsensored brushless motors by jmurba on Fri, 2022-08-05 12:05 |
3 |
by velolac Fri, 2022-08-12 22:14 |
General discussion | |
|
VESC 100/250 IO Ports Protection by luke.flecknell on Wed, 2022-03-30 06:49 |
2 |
by luke.flecknell Wed, 2022-03-30 12:41 |
General discussion | |
|
VESC 100/250 missing hall sensor plug by steve1428 on Sat, 2023-04-08 10:00 |
1 |
by iv.kravchenko Fri, 2023-05-19 22:26 |
General discussion | |
|
VESC 100/250 Voltage spikes? by LondonNight on Mon, 2022-09-05 08:21 |
2 |
by LondonNight Fri, 2022-09-09 18:01 |
General discussion | |
|
VESC 100/250 won't go full duty cycle by TheBennis on Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
VESC Original Hardware | |
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty on Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
General discussion | |
|
vesc 100250 Off-the-shelf motor by cuaxr on Mon, 2021-10-25 11:59 |
by cuaxr Mon, 2021-10-25 11:59 |
General discussion | ||
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi on Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
VESC Original Hardware | |
|
vesc 3.3 or 5v is shorted to GND by fer-bo on Fri, 2021-03-05 14:57 |
1 |
by fer-bo Fri, 2021-03-05 18:24 |
VESC Original Hardware | |
|
VESC 4.12 +5v output by lennarn on Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
VESC Original Hardware | |
|
VESC 4.12 - Current limited at 100A by Laerson on Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
VESC Tool | |
|
VESC 4.12 - Data loss on power off by da_rul0r on Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
VESC Original Hardware | |
|
vesc 4.12 2,3miliohm shunts firmware help by artteth on Sat, 2018-10-13 00:42 |
by artteth Sat, 2018-10-13 00:42 |
VESC Firmware | ||
|
vesc 4.12 disaster by stefann on Fri, 2020-05-08 18:54 |
2 |
by stefann Thu, 2020-05-14 19:28 |
Third Party Hardware | |
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 on Sun, 2019-10-13 14:22 |
by tahirali1 Sun, 2019-10-13 14:22 |
VESC Original Hardware | ||
|
VESC 4.12 firmware 3.38 flash back to firmware 2.18 by Arm007 on Thu, 2019-04-11 08:30 |
3 |
by skyline1970 Fri, 2019-08-02 15:15 |
VESC Firmware | |
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline on Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
General discussion | |
|
VESC 4.12 Hardware Bringup Checks by fureyc on Fri, 2021-04-02 20:56 |
by fureyc Fri, 2021-04-02 20:56 |
Third Party Hardware | ||
|
VESC 4.12 in a CityEL by twikis on Fri, 2018-01-12 15:54 |
6 |
by Roger Wolff Sat, 2018-01-20 16:14 |
General discussion | |
|
VESC 4.12 problems with FW newer then 3.10 by muchtete on Tue, 2019-01-29 18:37 |
2 |
by GunnarW Sun, 2019-02-24 11:53 |
VESC Firmware |
Pages
