You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
What's wrong with my motors? by Mads7400 on Fri, 2020-05-08 15:05 |
1 |
by tylr_r Wed, 2020-07-15 01:22 |
General discussion | |
|
Corrupted firmware by Phill Dixon on Mon, 2022-04-04 08:27 |
2 |
by Phill Dixon Mon, 2022-04-04 10:50 |
General discussion | |
|
Powering VESC and motor from powersupply by SIGURD on Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
General discussion | |
|
bldc_interface_set_current and bldc_interface_set_rpm troubles by kristof_lr on Wed, 2019-04-24 17:20 |
by kristof_lr Wed, 2019-04-24 17:20 |
General discussion | ||
|
Accessing the status LEDs by hrucker009 on Sun, 2020-01-05 20:09 |
1 |
by frank Tue, 2020-01-07 09:08 |
General discussion | |
|
Completely disabling regen current possibility on vesc by riraheta on Tue, 2022-11-29 01:48 |
3 |
by frank Wed, 2022-11-30 09:33 |
General discussion | |
|
Spin motor at constant ERPM while a button is pressed by t-dub-maui on Fri, 2024-01-26 07:33 |
by t-dub-maui Fri, 2024-01-26 07:33 |
General discussion | ||
|
Need some help on motor config and app config for Flypsky 65161 motor with FSESC75200 75V by freedomBoogie on Thu, 2021-03-04 09:30 |
2 |
by JoeSwe Sun, 2022-05-29 17:26 |
General discussion | |
|
Unofficial VESC Discord server by kubark42 on Tue, 2021-11-16 16:07 |
by kubark42 Fri, 2021-11-19 03:12 |
General discussion | ||
|
LED HW PWM?? by milom on Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
General discussion | |
|
display readings by FatsoBatso on Wed, 2021-02-24 18:01 |
by FatsoBatso Wed, 2021-02-24 18:01 |
General discussion | ||
|
Minimum speed by Davideo on Sat, 2017-10-21 17:40 |
7 |
by Davideo Thu, 2017-12-07 00:18 |
General discussion | |
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
Disabling speed cutoff by RDN2003 on Sat, 2020-10-24 00:25 |
1 |
by frank Tue, 2020-10-27 16:42 |
General discussion | |
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
VESC Battery Packs by frank on Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
General discussion | |
|
Custom code changes- I/O pin go high or low by dsuresh on Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
General discussion | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion |
Pages
