You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Sudden drop in speed after releasing throttle in FW mode by shokrabi on Sat, 2022-04-23 15:05 |
4 |
by DeuceDos Tue, 2023-05-30 09:54 |
General discussion | |
|
Problem with ADC, with no input voltage is 2.6-3.3 by komar on Fri, 2023-05-26 13:59 |
1 |
by dpeinado Wed, 2023-05-31 09:55 |
General discussion | |
|
Progetto Vesc by Matteo Christian on Tue, 2023-05-30 09:20 |
1 |
by frank Wed, 2023-05-31 11:30 |
General discussion | |
|
Comm conflict when connecting external imu? by Lennart Duijn on Wed, 2023-05-31 22:53 |
by Lennart Duijn Wed, 2023-05-31 22:53 |
VESC Tool | ||
|
Losing configuration and imu drift by AngelKillR on Sat, 2022-07-09 05:48 |
2 |
by Lennart Duijn Thu, 2023-06-01 18:24 |
Third Party Hardware | |
|
Trampa 100/250 with Cyc X1 Pro motor by Asi on Mon, 2023-05-22 17:33 |
1 |
by vadicus Thu, 2023-06-01 21:31 |
VESC Original Hardware | |
|
How can I make status packet, using arduino? by Medist on Thu, 2023-06-01 07:33 |
2 |
by toboli Thu, 2023-06-01 23:06 |
General discussion | |
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn on Thu, 2023-06-01 21:54 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
VESC Tool | ||
|
Bluemind 80V/450A and 100V/550A by qdxiatao on Fri, 2023-06-02 11:14 |
by qdxiatao Fri, 2023-06-02 11:14 |
General discussion | ||
|
VESC appears to loose sync when increasing throttle by srinath on Sun, 2023-06-04 04:11 |
by srinath Sun, 2023-06-04 04:11 |
General discussion | ||
|
Sensorless ERPM confusion and cogging in FOC by Addy on Mon, 2018-05-14 22:38 |
7 |
by bayetan Sun, 2023-06-04 17:19 |
General discussion | |
|
No load FOC stops when full FWD throttle. by toboli on Mon, 2023-06-05 18:41 |
by toboli Mon, 2023-06-05 18:41 |
General discussion | ||
|
(SOLVED) I2C, change pins by CTSchorsch on Mon, 2020-05-25 07:59 |
6 |
by woodmastr Tue, 2023-06-06 15:57 |
VESC Firmware | |
|
vesc for autonomous robots by _saeed_arabi_ on Tue, 2019-10-15 00:25 |
2 |
by Mayank Wed, 2023-06-07 00:05 |
General discussion | |
|
Not sure if parameter update in VESC tool works by srinath on Thu, 2023-06-08 11:29 |
by srinath Thu, 2023-06-08 11:29 |
VESC Tool | ||
|
Vesc 75100 by Matteo Christian on Wed, 2023-05-31 13:32 |
by Matteo Christian Fri, 2023-06-09 12:08 |
General discussion | ||
|
Data log field value detailed descriptions by Foilguy on Mon, 2023-06-12 20:59 |
1 |
by Foilguy Wed, 2023-06-14 16:12 |
VESC Tool | |
|
Can bus and Arduino by Snabelost on Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
General discussion | |
|
RPM and torque control modes by srinath on Fri, 2023-06-16 10:52 |
by srinath Fri, 2023-06-16 10:54 |
General discussion | ||
|
Hoverboard Motor, Noisy after FW update, Anti Cogging, PID values for low rpm by JulianT on Mon, 2023-02-13 10:50 |
1 |
by NolanCash Fri, 2023-06-16 16:58 |
Projects incorporating VESC technology |
Pages
