You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Third party Android/iOS app by vadicus on Tue, 2022-07-19 21:51 |
9 |
by teibill Sat, 2024-04-13 19:32 |
Third Party Hardware | |
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
Custom Apps by HammerHeadFett on Fri, 2020-07-17 00:10 |
9 |
by CTSchorsch Wed, 2021-12-22 09:12 |
VESC Tool | |
|
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan on Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
General discussion | |
|
(solved) Configuration smooth motordirection change by horak2084 on Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
VESC Firmware | |
|
Wireless Touch Displays - large and small by vadicus on Wed, 2023-01-25 02:59 |
9 |
by vadicus Wed, 2024-01-24 03:04 |
Third Party Hardware | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
|
Motor braking - shorting phases by rok340 on Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
General discussion | |
|
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
VESC Tool wont start by w31x on Wed, 2020-03-11 19:30 |
9 |
by SUB13 Sun, 2024-02-11 14:43 |
VESC Tool | |
|
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
|
ERPM to Rpm by faheemift on Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
General discussion | |
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
|
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
|
Help is there an issue with my new Vesc 6 by avis on Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
General discussion |
Pages
