You are here

Active forum topics

Topic Repliessort descending Last post Forum
Normal topic How to change HFI frequency
by gabbuman on Thu, 2021-04-08 10:12
by gabbuman
Thu, 2021-04-08 10:12
VESC Firmware
Normal topic Where to find CAN protocol documentation?
by doctarr on Tue, 2020-12-29 15:33
by doctarr
Tue, 2020-12-29 15:33
General discussion
Normal topic Throttle cutout or no response...MK6 + CA3 + Older Stand alone shunt
by craigoroszi on Tue, 2025-06-03 05:24
by craigoroszi
Tue, 2025-06-03 05:24
Third Party Hardware
Normal topic PID Speed Controller
by wysteria on Sat, 2020-12-12 10:14
by wysteria
Sat, 2020-12-12 10:14
General discussion
Normal topic UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish
by Shreeram2311 on Tue, 2025-05-06 02:40
by Shreeram2311
Tue, 2025-05-06 02:40
VESC Tool
Normal topic Generic dual drive Ebay controller speed
by stefann on Wed, 2022-03-23 21:14
by stefann
Wed, 2022-03-23 21:14
Third Party Hardware
Normal topic Noise related issues?
by RDN2003 on Sun, 2020-07-26 20:17
by RDN2003
Sun, 2020-07-26 20:17
General discussion
Normal topic Auto tune pid
by vcth on Mon, 2022-06-27 18:52
by vcth
Mon, 2022-06-27 18:52
VESC Tool
Normal topic VESC with no working brake button
by tavsanist on Sat, 2019-07-27 02:40
by tavsanist
Sat, 2019-07-27 02:40
General discussion
Normal topic Values truncated, but why?
by oger on Tue, 2020-03-24 17:43
by oger
Tue, 2020-03-24 17:43
VESC Tool
Normal topic Problems with UART communication via Arduino UNO
by Michael Hamm on Fri, 2022-02-04 13:29
by Michael Hamm
Fri, 2022-02-04 13:29
General discussion
Normal topic Flipsky6.6 usb not detected
by krom68 on Sat, 2019-02-23 10:21
by krom68
Wed, 2019-02-27 19:43
General discussion
Normal topic Why i cant insert a topic?
by SafrdA on Thu, 2021-04-29 20:41
by SafrdA
Thu, 2021-04-29 20:41
General discussion
Normal topic The engine stopped spinning after updating firmware
by brian adilman on Wed, 2022-01-26 17:40
by brian adilman
Wed, 2022-01-26 19:15
VESC Firmware
Normal topic HFI optimisation with increase in switching frequency
by rainebk@bigpond... on Tue, 2022-09-13 06:53
by rainebk@bigpond...
Tue, 2022-09-13 06:53
General discussion
Normal topic Do I need a motor with Hall sensor to use Vesc tool?
by greew on Sun, 2020-05-31 06:48
by greew
Sun, 2020-05-31 06:48
General discussion
Normal topic Why not using interrupt for Hall signal detection?
by kuan on Sun, 2021-01-03 09:51
by kuan
Sun, 2021-01-03 09:51
General discussion
Normal topic Help with FOC/PID parameter
by CTSchorsch on Thu, 2020-01-23 21:57
by CTSchorsch
Thu, 2020-01-23 21:57
General discussion
Normal topic D vs omega control
by rsarver on Wed, 2021-03-17 14:44
by rsarver
Wed, 2021-03-17 14:44
VESC Tool
Normal topic VESC specialist required.
by BlackPanthera on Mon, 2022-07-18 17:11
by BlackPanthera
Mon, 2022-07-18 17:11
General discussion

Pages

Subscribe to Active forum topics