You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 on Sun, 2023-02-05 18:00 |
3 |
by mvturnho Wed, 2025-05-14 08:46 |
VESC Firmware | |
|
BMS Harmony 16. Periodic annoying double-beeps. by SysGhost on Sun, 2026-05-03 22:34 |
3 |
by minimum Mon, 2026-05-25 08:37 |
VESC Original Hardware | |
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu on Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
VESC Original Hardware | |
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
Analog Throttle/Brake -- ADC2 does NOT cut power to the throttle? What is wrong? by 010203040506070809 on Fri, 2019-09-20 07:57 |
3 |
by striderkent Fri, 2019-09-20 21:54 |
General discussion | |
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake on Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
General discussion | |
|
Is there a way to use the 5 pin hall sensor with VESC? by Shivanshu Mahim on Fri, 2020-11-20 11:02 |
3 |
by Shivanshu Mahim Sat, 2020-11-21 19:34 |
General discussion | |
|
VESC 4.12 firmware 3.38 flash back to firmware 2.18 by Arm007 on Thu, 2019-04-11 08:30 |
3 |
by skyline1970 Fri, 2019-08-02 15:15 |
VESC Firmware | |
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly on Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
General discussion | |
|
Flipsky ESC 6.6 - How to Compile? [fixed] by hoeken on Tue, 2021-08-31 03:33 |
3 |
by alexantosh Wed, 2021-12-01 18:55 |
VESC Firmware | |
|
BitWizard ESC thermal Mod 100A cont. by Philipp Spindler on Thu, 2018-05-24 16:01 |
3 |
by Roger Wolff Thu, 2018-05-24 18:10 |
Third Party Hardware | |
|
4k monitor problem by nlabs on Wed, 2017-11-01 07:36 |
3 |
by benjamin Fri, 2017-11-03 09:22 |
VESC Tool | |
|
Vesc 6 MKIV ? by mchatain on Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
VESC Original Hardware | |
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin on Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
General discussion | |
|
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
|
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by thefallen Mon, 2021-03-01 16:42 |
VESC Tool | |
|
Open source hardware? by Jens on Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
General discussion | |
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
|
speed controller at low RPM by hagoston on Mon, 2021-03-08 13:54 |
3 |
by Elwin Sun, 2021-10-31 13:53 |
General discussion |
Pages
